G1018 Inventory, G1018HW Inventory | Grizzly G0500 manual

G1018 Inventory

•	Jointer Assembly w/Fence	........................1
•	V-Belt M52	2
•	Table Lever	2

•Hardware Bag #1

	—Combo Wrench 8/10MM	1
	—Combo Wrench 12/14MM	1
	—Allen Wrench 3MM	1
	—Allen Wrench 4MM	1
	—Allen Wrench 5MM	1
	—E-Clip	4
	—Jig Feet	2
	—Jig Rod	1
•	Hardware Bag #2
	—Lock Washers 3⁄8"	3
	—Special Mounting Bolts	3
•	Cutterhead Guard	1
•	Push Block	2
•	Stand Assembly w/Motor	1
• Stand Door Assembly w/Knob		1
•	Strain Relief	2
• Phillips Head Screw #10-24 x 11⁄4"		2
•	Flat Washers #10	2
•	Hex Nuts #10-24	2

Figure 8. G1018 Inventory.

G1018HW Inventory

•	Jointer Assembly w/Fence	........................1
•	V-Belt M52	2
•	Handwheel	2
•	Handle	2

•Hardware Bag #1

	—Combo Wrench 8/10MM	1
	—Combo Wrench 12/14MM	1
	—Allen Wrench 3MM	1
	—Allen Wrench 4MM	1
	—Allen Wrench 5MM	1
	—E-Clip	4
	—Jig Feet	2
	—Jig Rod	1
•	Hardware Bag #2
	—Lock Washers 3⁄8"	3
	—Special Mounting Bolts	3
•	Cutterhead Guard	1
•	Push Block	2
•	Stand Assembly w/Motor	1
• Stand Door Assembly w/Knob		1
•	Strain Relief	2
• Phillips Head Screw #10-24 x 11⁄4"		2
•	Flat Washers #10	2
•	Hex Nuts #10-24	2

Figure 9. G1018HW Inventory.

G0500/G1018/G1018HW 8" Jointers

-13-

Image 15

Grizzly G0500 instruction manual G1018 Inventory, G1018HW Inventory

Contents

Model G0500/G1018/G1018HW JointersPage Table of Contents Troubleshooting Guide 42-43 Safety Instructions For Power Tools Safety Length Never Joint end grain Additional Safety Instructions For Jointers Description G0500 G1018 G1018HW Introduction 220V Operation Circuit Requirements 110V Circuit Breaker Requirements 110V Operation 110V Operation GroundingExtension Cords 220V Operation Identification Common Terms and Definitions SET UP UnpackingG0500 Inventory G1018HW Inventory G1018 Inventory Measure Hardware Recognition Chart Site Considerations Clean Up Beginning Assembly Switch InstallationTo install the switch To connect the motor cord to the motor Wiring Connection To install the V-belt Jointer to StandBelt Stand Cover To install the stand cover Fence to Jointer G0500/G1018HW Handwheel InstallationTo install the fence on the jointer unit To install the handwheels on the Model G0500/G1018HW To assemble the knife setting gauge G1018 Table Lever InstallationKnife Setting Gauge To install the table levers on the Model G1018HW Knife Inspection Table AlignmentTo inspect the knife height Outfeed table check To adjust the infeed table G1018 Table Stops To set the Model G1018 outfeed table stop boltTo set the Model G1018 infeed table stop bolt To install the cutterhead guard This operation is extremely important for operator safetyCutterhead Guard To check and adjust the 45˚ R fence stop To check and adjust the 90˚ fence stopFence Stops Test Run Plug InstallationTo check and adjust the 45˚L fence stop To install a plug on your power cord Stock Inspection & Requirements Operations Squaring Stock Illustration of surface planing effects Surface Planing Illustration of edge jointing effects Edge Jointing Illustration of bevel cutting effects Bevel Cutting Illustration of rabbet cutting effects A few sample joints Rabbet Cutting Knife Condition MaintenanceGeneral Lubrication Date Approximate Hours Of Use Maintenance Performed To set the knives Service AdjustmentsAbout Service Setting Knives Table gibs To adjust the table gibs Adjusting Gibs To adjust the V-belt tension Adjusting V-Belts To adjust the V-belt alignment Replacing V-BeltTo replace the V-belts Date Approximate Hours Of Use Service Performed Reference Info Symptom Possible Cause Corrective Action Troubleshooting Guide See G0500/G1018/G1018HW Wiring Diagram Machine Data Sheet G0500 G0500 205 213 209 212 210 204211 202 208 201207 203 206 220 332 Base Cutterhead Model G1018 8 Jointer G1018 126 125 122 121 120 102 104 105 Table ADJ ROD 215 G1018 KNIVES, SET of Three Model G1018HW Jointer W/ Handwheels G1018HW 126 125 122 121 120 102 104 105 Rivet 2 X 5MM 202 205 211 203 204 210 213 209 212 208 207 201 206 214 G1018HW 328 PG1018323 Warranty and Returns Warranty Card BOX BELLINGHAM, WA Grizzly INDUSTRIAL, INC Call Today For a Free Full Color Catalog