TROUBLESHOOTING GUIDE

SYMPTOM

POSSIBLE CAUSE

CORRECTIVE ACTION

 

 

 

 

 

Motor will not start.

1.

Low voltage.

1.

Check power line for proper voltage.

 

2.

Open circuit in motor or loose connec-

2.

Inspect all lead connections on motor for loose or open connec-

 

 

tions.

 

tions.

 

 

 

 

 

Motor will not start; fuses or

1.

Short circuit in line cord or plug.

1.

Inspect cord or plug for damaged insulation and shorted wires.

circuit breakers blow.

2.

Short circuit in motor or loose connec-

2.

Inspect all connections on motor for loose or shorted terminals

 

 

tions.

 

or worn insulation.

 

3.

Incorrect fuses or circuit breakers in

3.

Install correct fuses or circuit breakers.

 

 

power line.

 

 

 

 

 

 

 

Motor overheats.

1.

Motor overloaded.

1.

Reduce load on motor.

 

2.

Air circulation through the motor

2.

Clean out motor to provide normal air circulation.

 

 

restricted.

 

 

 

 

 

 

 

Motor stalls (resulting in

1.

Short circuit in motor or loose connec-

1.

Inspect connections on motor for loose or shorted terminals or

blown fuses or tripped cir-

 

tions.

 

worn insulation.

cuit).

2.

Low voltage.

2

Correct the low voltage conditions.

 

3.

Incorrect fuses or circuit breakers in

3.

Install correct fuses or circuit breakers.

 

 

power line.

 

 

 

4.

Motor overloaded.

4.

Reduce load on motor.

 

 

 

 

 

Machine slows when oper-

1.

Applying too much pressure to work-

1.

Feed workpiece slower.

ating.

 

piece.

 

 

 

2.

V-belts loose.

2.

Adjust V-belts. See page 38-39.

 

 

 

 

 

Loud, repetitious noise com-

1.

Pulley setscrews or keys are missing or

1.

Inspect keys and setscrews. Replace or tighten if necessary.

ing from machine.

 

loose.

 

 

 

2.

Motor fan is hitting the cover.

2.

Tighten fan or shim cover.

 

3.

V-belts are defective.

3.

Replace V-belts. See page 39.

 

 

 

 

 

Snipe (gouge in the end of

1.

Outfeed table is set too low

1.

Align outfeed table with cutterhead knife at top dead center. See

the board that is uneven

 

 

 

page 22-23.

with the rest of the cut)

 

 

 

 

 

 

 

 

 

Workpiece stops in the mid-

1.

Outfeed table is set too high.

1.

Align outfeed table with cutterhead knife at top dead center. See

dle of the cut

 

 

 

page 22-23.

 

 

 

 

 

Chipping

1.

Knots or conflicting grain direction in

1.

Inspect stock for knots and grain.

 

 

wood.

 

 

 

2.

Dull knives.

2.

Inspect and sharpen cutterhead knives.

 

3.

Feeding too fast.

3.

Slow down the rate that you feed the wood into the cutterhead.

 

4.

Taking too deep of a cut.

4.

Raise the infeed table to take a smaller depth of cut. Never

 

 

 

 

exceed 18" per pass when edge jointing or 132" when surface

 

 

 

 

planing. Reduce cutting depth for harder woods.

 

 

 

 

 

Fuzzy grain

1.

Wood may have high moisture content

1.

Check moisture content and allow to dry if moisture is too high.

 

 

or surface wetness.

 

 

 

2.

Dull knives.

2.

Inspect and sharpen cutterhead knives.

 

 

 

 

 

Disconnect power to the machine when perform- ing any maintenance or repairs. Failure to do this may result in serious personal injury.

-42-

G0500/G1018/G1018HW 8" Jointers

Page 44
Image 44
Grizzly G0500 instruction manual Troubleshooting Guide, Symptom Possible Cause Corrective Action