Machine Data Sheet | Grizzly G0756 specification

MACHINE DATA

SHEET

Customer Service #: (570) 546-9663 · To Order Call: (800) 523-4777 · Fax #: (800) 438-5901

MODEL G0756 HEAVY-DUTY DRILLING MACHINE

Product Dimensions:
Weight	1026 lbs.
Width (side-to-side) x Depth (front-to-back) x Height	22 x 37 x 89-1/2 in.
Footprint (Length x Width)	29 x 20 in.
Shipping Dimensions:
Type	Wood Crate
Content	Machine
Weight	1202 lbs.
Length x Width x Height	90 x 28 x 45 in.
Must Ship Upright	No
Electrical:
Power Requirement	220V, 3-Phase, 60 Hz
Prewired Voltage	220V
Full-Load Current Rating	6.6A
Minimum Circuit Size	15A
Connection Type	Cord & Plug
Power Cord Included	No
Recommended Power Cord	“S”-Type, 4-Wire, 14 AWG, 300 VAC
Plug Included	No
Recommended Plug Type	15-15
Switch Type	Magnetic Switch w/Overload Protection
Recommended Phase Converter	G5844
Motors:
Coolant Pump
Type	Universal
Horsepower	60W
Phase	3-Phase
Amps	0.2A
Speed	1725 RPM
Power Transfer	Direct Drive
Bearings	Shielded & Permanently Lubricated
Main
Type	TEFC Induction
Horsepower	1-1/8 HP / 2 HP
Phase	3-Phase
Amps	6.4A
Speed	875 / 1725 RPM
Power Transfer	Gear Drive
Bearings	Shielded & Permanently Lubricated

Model G0756 (Mfg. Since 2/13)

-5-

Image 7

Grizzly G0756 owner manual Machine Data Sheet

Contents

Model G0756 Industrial Drill Press Page Table of Contents Machine Description Manual Accuracy IntroductionContact Info Identification Control Panel Machine Data Sheet Main Specifications Operation Info Safety Instructions for Machinery SafetyPage Safety for Drill Presses Circuit Requirements for Power SupplyAvailability Full-Load Current Rating 50 ft Grounding InstructionsExtension Cords Minimum Gauge Size 14 AWG Inventory see Figure Qty SetupNeeded for Setup UnpackingInventory Before cleaning, gather the following CleanupBasic steps for removing rust preventative Site Considerations Anchoring to Floor Lifting & PlacingAnchoring to Concrete Floors Initial Lubrication Arbor/Chuck AssemblyTo connect the drill chuck with the arbor To connect the power cord to the machine Power Connection Test Run Master power switch Model G0756 Mfg. Since 2/13 Emergency To test the coolant system Test Coolant System Spindle Break-In To perform the spindle break-in procedure Operations Tooling Installation RemovalOperations Overview Removing Tooling with Automatic Drift Installing Tapered ToolingRemoving Tooling Manually Rotating Table Depth StopTable Positioning Raising/Lowering Table To determine the needed RPM Selecting Spindle Drilling Mode Automatic Power Downfeed To use tapping mode Tapping Mode Coolant SystemTo operate the coolant system G1075-52-PC. Clamping Kit ACcESSORIES H7616 H7617 G3658-Titanium Drill Bits H8262-1⁄2 x MT#4 Keyless Chuck with Integral Shank H7819-Drill & Tap HSS 24 pc. Set Cleaning Protecting MaintenanceSchedule Oil Flow Sight Glass LubricationHeadstock Lubrication To change oil in headstock Ball Oilers Changing Coolant Motor & Electrical ServiceTroubleshooting Symptom Possible Cause Possible Solution Drill Press Operations Torque Limiter Replacing Lamp BulbTo replace the bulb in the work lamp Wiring Safety Instructions Wiring Component Location Index Wiring Overview Plug Power Connection WiringElectric Clutch Wiring Hot 220 VAC Spindle motor wiring Motor & Pump Wiring Viewed from behind Control Panel & Limit Switches QM5 QM3 QM2 QM1 Electrical Panel Wiring Electrical wiring panel Model G0756 Mfg. Since 2/13 Electrical Wiring Panel Photo Table Support & Coolant Breakdown Parts Description Table Support & Coolant Parts List Gearbox Breakdown Gearbox Breakdown Gearbox Parts List Spindle Feed Breakdown Spindle Feed Parts List Headstock Breakdown Headstock Breakdown Headstock Parts List Electrical Parts Breakdown Description Electrical Parts List 506 502 503 501 508 509 507 510 504 511 505 512 513 Labels & Cosmetics Comments Warranty Card BOX BELLINGHAM, WA Grizzly INDUSTRIAL, INC Warranty & Returns