Name of Parts | Wire Controller |
13 | 14 | 15 16 | 17 | 18 | 19 |
|
| 22.Setting button | ||
|
|
|
|
|
|
|
| |||
12 |
|
|
|
|
|
|
|
|
| Used to confirm |
|
|
|
|
|
|
|
|
|
| |
11 |
|
|
|
|
|
|
|
|
| the time of timer |
10 |
|
|
|
|
|
|
|
|
| |
|
|
| ** | ** | ** |
|
|
| and clock | |
8 | AUTO |
|
| ** |
|
| 20 |
| 23.Sleep button | |
9 |
|
|
|
|
|
|
|
|
| |
7 |
|
|
| ** |
| ** | 21 |
|
| Used to set Sleep |
|
|
|
| 22 |
|
| ||||
6 |
|
|
|
|
|
|
|
| state or Power | |
** |
|
| ** |
| ** | 23 |
|
| ||
5 | ** |
|
|
|
|
|
|
| Failure Resume | |
|
|
|
|
| 24 |
|
| |||
4 |
|
|
| ** | **** | ** |
|
| Function | |
|
|
|
|
| 25 |
|
| |||
|
|
|
|
|
|
|
| 24.Time Adjusting | ||
3 |
|
|
|
|
|
| 26 |
| ||
|
|
|
| **/** |
|
| 27 |
|
| button |
|
|
|
|
|
|
|
|
|
| |
2 |
|
|
|
|
|
| 28 |
|
| Used to adjust the |
1 |
|
|
|
|
|
|
|
| ||
|
|
|
|
|
| 29 |
|
| ||
1.ON/OFF button |
| 13.Sleep state display |
|
|
| time of timer and | ||||
Used to turn on/off unit |
| 14.Network control display |
|
| clock | |||||
2.Temperature display |
| 15.Working mode display |
|
|
| 25.Reset button | ||||
3.Clock display |
| Working | Auto |
| Cooling Dehumidifying | Heating | Fan |
| When the wire | |
4.Timer ON/OFF display | mode | operation operation operation | operation operation | |||||||
Wire |
|
|
|
|
|
| controller appears | |||
5.Humidity display |
| controller |
|
|
|
|
|
| abnormal condition, | |
6.Air filter cleaning display | 16.Electric heating display |
|
|
| use a | |||||
When there is too much dust |
| 17.Operation mode button |
|
|
| article to press this | ||||
|
|
|
| button to make the | ||||||
collected on the air inlet, the |
| Used to set working mode: |
|
| ||||||
wire controller will show |
|
|
|
| wire controller | |||||
|
| Auto, Cooling, Dehumidifying, |
| |||||||
this display to remind the |
|
|
| resume normal | ||||||
|
| Heating, Fan |
|
|
| |||||
user to clean the air inlet. |
|
|
|
|
| 26.Air Filter Reset | ||||
After cleaning and installation, |
| 18.Fan speed button |
|
|
| |||||
just press the air filter reset button. |
| Used to set fan speed: Low |
|
| button | |||||
7.Super/Soft operation display |
| Fan, Med Fan, High Fan, Auto |
| After cleaning the | ||||||
8.Fan speed display |
|
| 19.Swing button |
|
|
| air inlet, press this | |||
Auto |
| Used to set Auto Swing or |
|
| button, the unit | |||||
|
|
|
|
| ||||||
Low Fan Med Fan High Fan Auto |
|
| Fixed air sending direction |
|
| can start to operate | ||||
| 20.Temperature Setting button |
| 27.Timer button | |||||||
9.Auto Swing display |
|
| ||||||||
|
| Used to set temperature, |
|
| Used to set the | |||||
10.Health state display |
|
| temperature range: 16*~30* |
|
| mode of timer | ||||
11.Fresh air state display |
| 21.Clock button |
|
| 28.Lock state display | |||||
12.Humidifying state display |
| Used to calibrate the time of |
| 29.Electric heating button | ||||||
|
|
| timer and clock |
|
|
|
|
Note:
1.This model does not have the following related display and function * * 10 11 12 28
display 16
Calibration of clock
When turning on the unit for the first time, the clock should be calibrated. The method of calibration is:
1.Press “Clock” button, the Clock display “AM” “PM” will flash.
2.Press * or * to adjust time. For each press, the time will increase or*decrease 1 *minute. If depressing the button, the time will increase or decrease*rapidly. 3.After confirming the time, press “Set” button, “AM” or “PM” will stop flashing, *the clock will begin to work.
4