Installation and Connections
After unpacking the unit, and placing it on a solid surface capable of supporting its weight, you will need to make the connections to your audio and video equipment.
Audio Equipment Connections
We recommend that you use
When making connections to audio source equipment or speakers it is always a good prac- tice to unplug the unit from the AC wall outlet. This prevents any possibility of accidentally send- ing audio or transient signals to the speakers that may damage them.
1. Connect the analog output of a CD player to the CD inputs .
NOTE: When the CD player has both fixed and variable audio outputs it is best to use the fixed output unless you find that the input to the receiver is so low that the sound is noisy, or so high that the signal is distorted.
2.Connect the analog Play/Out jacks of a cas- sette deck, MD,
the Tape Input jacks . Connect the analog Record/In jacks on the recorder to the Tape
Output jacks | on the AVR. |
3.Connect the digital output of any digital sources such as a CD or DVD changer or player, advanced video game, a digital satellite receiver, HDTV tuner or digital cable
*Ó.
4.Connect the Coaxial or Optical Digital
Outputs on the rear panel of the AVR to the matching digital input connections on a
5.Assemble the AM Loop Antenna supplied with the unit as shown below. Connect it to the AM
and GND screw terminals .
6. Connect the supplied FM antenna to the FM
(75 ohm) connection . The FM antenna may be an external roof antenna, an inside powered or wire lead antenna or a connection from a cable system. Note that if the antenna or connec- tion uses
7. Connect the front, center and surround speak-
er outputs | to the respective speakers. |
To assure that all the audio signals are carried to your speakers without loss of clarity or resolu- tion, we suggest that you use
Regardless of the brand of cable selected, we rec- ommend that you use a cable constructed of fine, multistrand copper with an area greater than
2 mm2.
Cable with an area of 1.5 mm2 may be used for short runs of less than 4 m. We do not recom- mend that you use cables with an area less than 1mm2 due to the power loss and degradation in performance that will occur.
Cables that are run inside walls should have the appropriate markings to indicate listing with any appropriate testing agency standards. Questions about running cables inside walls should be referred to your installer or a licensed electrician who is familiar with the applicable local building codes in your area.
When connecting wires to the speakers, be cer- tain to observe proper polarity. Note that the positive (+) terminal of each speaker connection now carries a specific color code as noted on page 8. However, most speakers will still use a red terminal for the postive (+) connection. Connect the “negative” or “black” wire to the same terminal on both the receiver and the speaker.
NOTE: While most speaker manufacturers adhere to an industry convention of using black terminals for negative and red ones for positive, some manufacturers may vary from this configu- ration. To assure proper phase and optimal per- formance, consult the identification plate on your speaker or the speaker’s manual to verify polarity. If you do not know the polarity of your speaker, ask your dealer for advice before proceeding, or consult the speaker’s manufacturer.
We also recommend that the length of cable used to connect speaker pairs be identical. For example, use the same length piece of cable to connect the
8.Connections to a subwoofer are normally made via a line level audio connection from the
Subwoofer Output to the
passive subwoofer is used, the connection first goes to a power amplifier, which will be connect- ed to one or more subwoofer speakers. If you are using a powered subwoofer that does not have
9.If an external
6-Channel Direct Inputs .
10.If an external
.
11.If you plan to use a 7.1 channel source or wish to take advantage of the 6.1/7.1 channel processing modes such as THX Surround EX or
to the inputs of the amplifier feeding those channels' speakers.
Video Equipment Connections
Video equipment is connected in the same manner as audio components. Again, the use of
1.Connect a VCR’s audio and video Play/Out jacks to the Video 1/ Video 2 Input Jacks on the rear panel. The Audio and Video Record/In jacks on the VCR should be connected to the
Video 1/ Video 2 Output Jacks | on the |
AVR. |
|
2.Connect the analog audio and video outputs of a satellite receiver, cable TV converter or television set or any other video source to the
Video 3/ Video 4 Input Jacks | jacks. |
3.Connect the analog audio and video outputs of a DVD or laser disc player to the DVD Inputs .
4.Connect the digital audio outputs of a CD, MD or DVD player, satellite receiver, cable box or HDTV converter to the appropriate Optical or
Coaxial Digital Inputs | *Ó. |
INSTALLATION AND CONNECTIONS 15