Manuals / Honeywell / Household Appliance / Home Security System

Honeywell 6271V manual System Overview contd, To Exit the Safe Mode

Models: 6271V

1 72

Download 72 pages 57.6 Kb

Page 12

To Exit the Safe Mode:

System Overview (cont'd)

Note that this is a limited mode of operation. While in this mode:

•You can use the Security button to access the Console Emulation Mode of operation to try to clear your faults, disarm the system, or enter additional Alpha Keypad commands specified in you panel User Guide. You can perform almost all functions that you can perform from a standard non-graphic alpha keypad.

•You can depress the “Panic” key and generate Emergency Messages as defined in the panels home partition for this TouchCenter.

•The Armed and Ready LEDs on the front of the TouchCenter will indicate the TouchCenter’s home partition status. The Message LED is not active in the Safe Mode.

•The Chime mode will function in the Safe Mode: however, you will not have Voice, Voice Chime, or Message capability.

•When in Safe Mode, the lock on the Security button on the Home screen will always be shown in the unlocked position. Refer to the Armed LED for the true armed status of your system.

•When an alarm occurs in the Safe Mode, it is displayed on the Console mode screen only. It will not be shown on the Home screen.

To Exit the Safe Mode:

1.Press the ! SAFE MODE ! bar. You will be presented with the following popup message:

2.Select “Yes” to return to the Normal Mode of operation. The TouchCenter will reset and normal operation will return as long as the original conditions that caused the entry into Safe Mode do not still exist.

12

Image 12

Honeywell 6271V manual System Overview contd, To Exit the Safe Mode

Contents

User Guide ADEMCO TouchCenter KeypadK10498 8/05 Rev. A Table of Contents AlarmsMemory of Alarm FIRE ALARM SYSTEM OPERATIONTable of Contents Contd ADVANCED SYSTEM FEATURESTOUCHCENTER SETUP VOICE MESSAGESAbout the TouchCenter IntroductionThe TouchCenter Interface About the TouchCenter Contd Navigating through the TouchCenterAbout Your Home Screen About the TouchCenter contd Navigation Icon DescriptionsICON LOCATIONTouchCenter Arming Screen About the TouchCenter ContdFUNCTION AWAYSystem Troubles actual settings of this modeAbout the TouchCenter contd FUNCTIONSystem Overview Introduction to Your SystemBurglary Protection PartitionsAlarms Memory of AlarmSystem Overview contd Fire ProtectionSystem Overview Contd User CodesExtended Functionality Safe ModeSystem Overview contd To Exit the Safe ModeHow to Arm the System Security System OperationIntroduction to Security System Operation Security System Operation contd SCREENACTION How to Arm Multiple Partitions Security System Operation ContdSCREEN ACTIONHow to Display Faults Security System Operation contdSCREEN ACTIONSecurity System Operation Contd How to Bypass Zones Security System Operation contdTo bypass zones do the following SCREENSecurity System Operation Contd SCREENACTION 5. Press the BYPASS SELECTEDSecurity System Operation contd SCREENACTION How to Remove Bypassed Zones Security System Operation ContdSCREEN ACTION3.The User Authorization screen is Security System Operation contdSCREEN ACTIONHow to Disarm the System To disarm the system when entering the premisesSecurity System Operation Contd To disarm the system when already in the premises Security System Operation contdSCREEN ACTIONSecurity System Operation Contd SCREENACTION How to Check the Status of Other Partitions Security System Operation contd3.Enter the code authorized to access other partitions Security System Operation ContdSCREEN ACTIONHow to Send Emergency Messages Security System Operation contdHow to View the Event Log Security System Operation ContdWhen All Partitions or All Events Security System Operation contdSCREEN ACTIONFire Alarm System Operation Introduction to Fire Alarm System OperationIn Case of Fire Alarm Silencing and Clearing a Fire AlarmFire Alarm System Operation contd User Code Setup Introduction to User Code SetupAuthority Levels User Code Setup contd How to Access User SetupSCREEN ACTIONUser Code Setup Contd How to Add a UserSCREEN ACTIONUser Code Setup contd SCREENACTION Enter User Code… displayedUser Code Setup Contd SCREENACTION selected, the Allow Arm/Disarm fromUser Code Setup contd 10.If this user is assigned an RF button zone, touch the box below the RF Button Zone. The RF Button Zone screen is displayed with the instructions to enter 2 or 3 digits based on the alarm system being used. Enter the RF Button Zone number that was previously programmed in the control panel. Note that the RF Button Zone does not appear for every user.The User Options screen will be redisplayedSCREEN ACTIONHow to Delete a User User Code Setup ContdSCREEN ACTIONHow to Edit a User User Code Setup contdSCREEN ACTIONUser Code Setup Contd SCREENACTION Advanced System Features Introduction to Advanced System FeaturesHow to Enter Console Emulation Mode Console Emulation ModeAdvanced System Features Contd SCREENACTION Voice Messages Introduction to Recording and Retrieving MessagesMessage Center Screen Voice Messages Contd Recording a Voice MessageSCREEN ACTIONRetrieving and Deleting a Voice Message Voice Messages ContdTo retrieve a voice message, do the following SCREENSummary of TouchCenter LED Operation TouchCenter LED OperationTouchCenter Setup How to Access TouchCenter Setup OptionsHow to Access Setup TouchCenter Setup Contd SCREENACTION TouchCenter Setup contd How to Adjust the Touch Screen ContrastTouch Screen Contrast Control How to Adjust the Volume TouchCenter Volume ControlTouchCenter Setup Contd TouchCenter Setup contd SCREENACTION Backlight Off After arrow button. ATouchCenter Setup Contd button. A Settings Changed! pop-upSCREEN ACTIONHow to Select Homepage After Time TouchCenter Setup contdTouchCenter Setup Contd button. A Settings Changed! pop-upSCREEN ACTIONHow to Set the Time and Date TouchCenter Setup contdTouchCenter Setup Contd 3.Select if you want a 12-houror 24-hourformat for your time display by touching the circle to the left of the 12 Hour display in the “Settings” area of the screen. A check mark in the circle indicates a 12- hour display formatSCREEN ACTIONTouchCenter Setup contd SCREENACTION Enter 2 digits for the hourTouchCenter Setup Contd SCREENACTION 14.Enter the two digits for the current minuteHow to Access Operating Modes TouchCenter Operating ModesOperating Modes Chime, Voice, and Voice Chime TouchCenter Operating Modes Contd SCREENACTION 3. Press the OPERATING MODESHow to Clean your TouchCenter Maintaining Your SystemSCREEN ACTIONMaintaining Your System Contd Routine CareGlossary Glossary Contd Page Page Page Page Page Page ÊK10498 Š ONE YEAR LIMITED WARRANTY