Manuals / Honeywell / Household Appliance / Home Security System

Honeywell 6271V How to Delete a User, User Code Setup Contd, Screen, Action, Authorized Code

Models: 6271V

1 72

Page 39

	User Code Setup (Cont'd)
How to Delete a User
Delete a User as follows:

SCREEN	ACTION

	1. From the User Setup screen, touch
	the circle next to the user to be deleted
	and press the DELETE USER button.
	The "User Authorization" screen is
	displayed with the instructions "Enter
	Authorized Code:".

	2. Enter your Authorized code. The
	“Delete Confirmation” screen is displayed.
	Note: The authorized code for deleting
	users is dependent upon the system you
	have. Check with your system installer to
	determine who can delete users.

	3. Press the appropriate button. The
	User Setup screen is displayed.

Page 39

Image 39

Honeywell 6271V manual How to Delete a User, User Code Setup Contd, Screen, Action, Authorized Code

Contents

User Guide ADEMCO TouchCenter KeypadK10498 8/05 Rev. A Memory of Alarm Table of ContentsEntry/Exit Delays AlarmsVOICE MESSAGES Table of Contents ContdADVANCED SYSTEM FEATURES TOUCHCENTER SETUPAbout the TouchCenter IntroductionThe TouchCenter Interface About the TouchCenter Contd Navigating through the TouchCenterAbout Your Home Screen LOCATION About the TouchCenter contdNavigation Icon Descriptions ICONAWAY TouchCenter Arming ScreenAbout the TouchCenter Contd FUNCTIONFUNCTION System Troublesactual settings of this mode About the TouchCenter contdPartitions System OverviewIntroduction to Your System Burglary ProtectionSystem Overview contd Entry/Exit DelaysAlarms Memory of AlarmSafe Mode System Overview ContdUser Codes Extended FunctionalityTo Exit the Safe Mode System Overview contdHow to Arm the System Security System OperationIntroduction to Security System Operation Security System Operation contd SCREENACTION ACTION How to Arm Multiple PartitionsSecurity System Operation Contd SCREENACTION How to Display FaultsSecurity System Operation contd SCREENSecurity System Operation Contd SCREEN How to Bypass ZonesSecurity System Operation contd To bypass zones do the following5. Press the BYPASS SELECTED Security System Operation ContdSCREEN ACTIONSecurity System Operation contd SCREENACTION ACTION How to Remove Bypassed ZonesSecurity System Operation Contd SCREENACTION 3.The User Authorization screen isSecurity System Operation contd SCREENHow to Disarm the System To disarm the system when entering the premisesSecurity System Operation Contd ACTION To disarm the system when already in the premisesSecurity System Operation contd SCREENSecurity System Operation Contd SCREENACTION Security System Operation contd How to Check the Status of Other PartitionsACTION 3.Enter the code authorized to access other partitionsSecurity System Operation Contd SCREENSecurity System Operation contd How to Send Emergency MessagesSecurity System Operation Contd How to View the Event LogACTION When All Partitions or All EventsSecurity System Operation contd SCREENSilencing and Clearing a Fire Alarm Fire Alarm System OperationIntroduction to Fire Alarm System Operation In Case of Fire AlarmFire Alarm System Operation contd User Code Setup Introduction to User Code SetupAuthority Levels ACTION User Code Setup contdHow to Access User Setup SCREENACTION User Code Setup ContdHow to Add a User SCREENEnter User Code… displayed User Code Setup contdSCREEN ACTIONselected, the Allow Arm/Disarm from User Code Setup ContdSCREEN ACTIONACTION User Code Setup contd10.If this user is assigned an RF button zone, touch the box below the RF Button Zone. The RF Button Zone screen is displayed with the instructions to enter 2 or 3 digits based on the alarm system being used. Enter the RF Button Zone number that was previously programmed in the control panel. Note that the RF Button Zone does not appear for every user.The User Options screen will be redisplayed SCREENACTION How to Delete a UserUser Code Setup Contd SCREENACTION How to Edit a UserUser Code Setup contd SCREENUser Code Setup Contd SCREENACTION Console Emulation Mode Advanced System FeaturesIntroduction to Advanced System Features How to Enter Console Emulation ModeAdvanced System Features Contd SCREENACTION Voice Messages Introduction to Recording and Retrieving MessagesMessage Center Screen ACTION Voice Messages ContdRecording a Voice Message SCREENSCREEN Retrieving and Deleting a Voice MessageVoice Messages Contd To retrieve a voice message, do the followingTouchCenter LED Operation Summary of TouchCenter LED OperationTouchCenter Setup How to Access TouchCenter Setup OptionsHow to Access Setup TouchCenter Setup Contd SCREENACTION TouchCenter Setup contd How to Adjust the Touch Screen ContrastTouch Screen Contrast Control How to Adjust the Volume TouchCenter Volume ControlTouchCenter Setup Contd Backlight Off After arrow button. A TouchCenter Setup contdSCREEN ACTIONACTION TouchCenter Setup Contdbutton. A Settings Changed! pop-up SCREENTouchCenter Setup contd How to Select Homepage After TimeACTION TouchCenter Setup Contdbutton. A Settings Changed! pop-up SCREENTouchCenter Setup contd How to Set the Time and DateACTION TouchCenter Setup Contd3.Select if you want a 12-houror 24-hourformat for your time display by touching the circle to the left of the 12 Hour display in the “Settings” area of the screen. A check mark in the circle indicates a 12- hour display format SCREENEnter 2 digits for the hour TouchCenter Setup contdSCREEN ACTION14.Enter the two digits for the current minute TouchCenter Setup ContdSCREEN ACTIONHow to Access Operating Modes TouchCenter Operating ModesOperating Modes Chime, Voice, and Voice Chime 3. Press the OPERATING MODES TouchCenter Operating Modes ContdSCREEN ACTIONACTION How to Clean your TouchCenterMaintaining Your System SCREENRoutine Care Maintaining Your System ContdGlossary Glossary Contd Page Page Page Page Page Page ONE YEAR LIMITED WARRANTY ÊK10498 Š

How to Delete a User

Authorized Code:".