Manuals / Honeywell / Household Appliance / Home Security System

Honeywell 6271V manual Security System Operation Contd, Screen, Action, Press the BYPASS SELECTED

Models: 6271V

1 72

Page 19

Security System Operation (Cont'd)

	SCREEN	ACTION


		4. Highlight the zone(s) to be bypassed
		by touching it on the screen when the
		zones are displayed.

		5. Press the BYPASS SELECTED
		button. The "User Authorization" screen
		is displayed with the instructions "To
		Bypass Zones, Enter Code".
		Note: If zones have already been
		bypassed, the top of this screen will
		indicate “Ready Bypass” and the screen
		will contain a Clear Bypasses button.

		6. Enter your 4-digit user code. The
		"More Choices" screen is displayed
		showing the system status as Ready-
		Bypass

Page 19

Image 19

Honeywell 6271V manual Security System Operation Contd, Screen, Action, Press the BYPASS SELECTED, Bypass Zones, Enter Code

Contents

ADEMCO TouchCenter Keypad User GuideK10498 8/05 Rev. A Memory of Alarm Table of ContentsEntry/Exit Delays AlarmsVOICE MESSAGES Table of Contents ContdADVANCED SYSTEM FEATURES TOUCHCENTER SETUPIntroduction About the TouchCenterThe TouchCenter Interface Navigating through the TouchCenter About the TouchCenter ContdAbout Your Home Screen LOCATION About the TouchCenter contdNavigation Icon Descriptions ICONAWAY TouchCenter Arming ScreenAbout the TouchCenter Contd FUNCTIONFUNCTION System Troublesactual settings of this mode About the TouchCenter contdPartitions System OverviewIntroduction to Your System Burglary ProtectionSystem Overview contd Entry/Exit DelaysAlarms Memory of AlarmSafe Mode System Overview ContdUser Codes Extended FunctionalityTo Exit the Safe Mode System Overview contdSecurity System Operation How to Arm the SystemIntroduction to Security System Operation SCREEN Security System Operation contdACTION ACTION How to Arm Multiple PartitionsSecurity System Operation Contd SCREENACTION How to Display FaultsSecurity System Operation contd SCREENSecurity System Operation Contd SCREEN How to Bypass ZonesSecurity System Operation contd To bypass zones do the following5. Press the BYPASS SELECTED Security System Operation ContdSCREEN ACTIONSCREEN Security System Operation contdACTION ACTION How to Remove Bypassed ZonesSecurity System Operation Contd SCREENACTION 3.The User Authorization screen isSecurity System Operation contd SCREENTo disarm the system when entering the premises How to Disarm the SystemSecurity System Operation Contd ACTION To disarm the system when already in the premisesSecurity System Operation contd SCREENSCREEN Security System Operation ContdACTION Security System Operation contd How to Check the Status of Other PartitionsACTION 3.Enter the code authorized to access other partitionsSecurity System Operation Contd SCREENSecurity System Operation contd How to Send Emergency MessagesSecurity System Operation Contd How to View the Event LogACTION When All Partitions or All EventsSecurity System Operation contd SCREENSilencing and Clearing a Fire Alarm Fire Alarm System OperationIntroduction to Fire Alarm System Operation In Case of Fire AlarmFire Alarm System Operation contd Introduction to User Code Setup User Code SetupAuthority Levels ACTION User Code Setup contdHow to Access User Setup SCREENACTION User Code Setup ContdHow to Add a User SCREENEnter User Code… displayed User Code Setup contdSCREEN ACTIONselected, the Allow Arm/Disarm from User Code Setup ContdSCREEN ACTIONACTION User Code Setup contd10.If this user is assigned an RF button zone, touch the box below the RF Button Zone. The RF Button Zone screen is displayed with the instructions to enter 2 or 3 digits based on the alarm system being used. Enter the RF Button Zone number that was previously programmed in the control panel. Note that the RF Button Zone does not appear for every user.The User Options screen will be redisplayed SCREENACTION How to Delete a UserUser Code Setup Contd SCREENACTION How to Edit a UserUser Code Setup contd SCREENSCREEN User Code Setup ContdACTION Console Emulation Mode Advanced System FeaturesIntroduction to Advanced System Features How to Enter Console Emulation ModeSCREEN Advanced System Features ContdACTION Introduction to Recording and Retrieving Messages Voice MessagesMessage Center Screen ACTION Voice Messages ContdRecording a Voice Message SCREENSCREEN Retrieving and Deleting a Voice MessageVoice Messages Contd To retrieve a voice message, do the followingTouchCenter LED Operation Summary of TouchCenter LED OperationHow to Access TouchCenter Setup Options TouchCenter SetupHow to Access Setup SCREEN TouchCenter Setup ContdACTION How to Adjust the Touch Screen Contrast TouchCenter Setup contdTouch Screen Contrast Control TouchCenter Volume Control How to Adjust the VolumeTouchCenter Setup Contd Backlight Off After arrow button. A TouchCenter Setup contdSCREEN ACTIONACTION TouchCenter Setup Contdbutton. A Settings Changed! pop-up SCREENTouchCenter Setup contd How to Select Homepage After TimeACTION TouchCenter Setup Contdbutton. A Settings Changed! pop-up SCREENTouchCenter Setup contd How to Set the Time and DateACTION TouchCenter Setup Contd3.Select if you want a 12-houror 24-hourformat for your time display by touching the circle to the left of the 12 Hour display in the “Settings” area of the screen. A check mark in the circle indicates a 12- hour display format SCREENEnter 2 digits for the hour TouchCenter Setup contdSCREEN ACTION14.Enter the two digits for the current minute TouchCenter Setup ContdSCREEN ACTIONTouchCenter Operating Modes How to Access Operating ModesOperating Modes Chime, Voice, and Voice Chime 3. Press the OPERATING MODES TouchCenter Operating Modes ContdSCREEN ACTIONACTION How to Clean your TouchCenterMaintaining Your System SCREENRoutine Care Maintaining Your System ContdGlossary Glossary Contd Page Page Page Page Page Page ONE YEAR LIMITED WARRANTY ÊK10498 Š