HP 449298-001 specification

alternate Virtual Connect Ethernet module. This feature can be useful when troubleshooting the Virtual Connect manager. The network and FC processing of the Virtual Connect subsystem is not disturbed during the restart or failover of the Virtual Connect Manager.

If the command line option -failoveris included in the reset vcm command and a Virtual Connect Ethernet module is available in the alternate I/O bay (I/O Bays 1 and 2 can host the Virtual Connect Manager), the command line displays the message:

SUCCESS: The Virtual Connect Manager is being reset. Please wait...

The user is logged out of the session after approximately 1 minute. An attempted login to the same Virtual Connect Ethernet Module is rejected with the message:

Virtual Connect Manager not found at this IP address.

If the user attempts to login to the alternate I/O bay, they might receive the error message during the attempted login:

Unable to communicate with the Virtual Connect Manager. Please retry again later.

The login should succeed after the Virtual Connect Manager has restarted on this alternate Virtual Connect Ethernet module. Allow up to 5 minutes, depending on the enclosure configuration.

If the command line option -failoveris not included in the reset vcm command or a Virtual Connect Ethernet module is not available in the alternate I/O bay, the command line displays the message:

SUCCESS: The Virtual Connect Manager is being reset. Please wait...

The user is logged out of the session after approximately 1 minute. If the user attempts to re-login they might receive the error message during the attempted login:

Unable to communicate with the Virtual Connect Manager. Please retry again later.

The login should succeed after the Virtual Connect Manager has restarted. Allow up to 5 minutes, depending on the enclosure configuration.

Configuring the Virtual Connect domain using the CLI 52

Image 52

HP 449298-001 manual Virtual Connect Manager not found at this IP address

Contents

HP Virtual Connect Manager Command Line Interface User Guide Audience assumptions Contents Technical support Introduction Command line overviewVirtual Connect overview Command line syntax Subcommand managed element parameters options propertiesParameters Options CLI command execution modes Properties Remote access to the Virtual Connect Manager Subcommands Command lineManaged elements Devicebay Domain Supported actions delete, help, set, show Enclosure Enet-connection Supported actions add, help, remove, set Network=SomeNetwork2 PXE=enabled AddressType=Factory-DefaultAddressType EthernetMAC External-manager Fabric Fc-connection Support actions help, show, update Firmware Igmp Interconnect Ldap Ldap-group Supported actions add, help, remove, set, show Mac-cache Network Profile Add profile MyNewProfile2 -NoDefaultEnetConn Add profile MyNewProfile2 -NoDefaultFcConnAdd profile MyNewProfile Assign profile Supported actions help, poweroff, poweron, reboot, show Server Poweroff server enc02 Poweroff server enc02 -ForcePoweroff server enc0 Poweroff server enc02 -ForceOnTimeout Stackinglink Systemlog StatusUplinkport Set uplinkport Set uplinkport PortID Network=NetworkNameSpeed=Auto10Mb100Mb1GbDisabled Set uplinkport enc012 Network=MyNetwork Speed=1Gb Uplinkset User Set user steve Password=fgY87hHl Set user steve PasswordSet user bill Password=HGtwf7272562 Remove user steve Vcm Help subsystemVersion Command line Output format Interactive user output format Brad Domain Brad Mills Brad.mills@hp.com True Server Scriptable output format Command line Configuring the Virtual Connect domain using the CLI Basic configurationSsh 192.168.0.120 login as Administrator password Ssh 192.168.0.120 login as Administrator Domain setup Setting the domain nameConfiguring local users Importing an enclosure Add user bob password=fhkjdhfk privileges=domain,network Set user bob fullname=Bob J Smith enabled=falseRemove user bob Remove user Configuring Ldap authentication support for users Network setupConfiguring MAC Address ranges Assigned MAC addresses Adding uplink ports to an enet-network Creating an enet-networkCreating a shared uplink port set Fibre Channel setup Configuring WWN address rangesAdding uplink ports to a shared uplink port set Creating a network that uses a shared uplink port set Server Profile setup Modifying FC fabric propertiesDisplaying FC fabrics Set fabric name=MyNewName portspeed=4Gb Configuring the Virtual Connect domain using the CLI Configuring Igmp settings Creating server profilesAdding enet-network connections to a profile Adding FC fabric connections to a server profile Configuring MAC cache failover settings Set mac-cache enabled=true refresh=10Common management operations Logging out of the CLI Resetting the Virtual Connect Manager Reset vcm Reset vcm -failover Virtual Connect Manager not found at this IP address Before you contact HP Technical supportHP contact information Acronyms and abbreviations Igmp PXE Index Index