Manuals / Husqvarna / Lawn and Garden / Lawn Mower

Husqvarna Rider 155 manual Restoring from service position, Maintenance

Models: Rider 155

1 52

Download 52 pages 32.31 Kb

Page 40

Image 40

MAINTENANCE

WARNING!

Observe caution to avoid trapping your hand.

8. Lift off the drive belt (1). Then pull out the pin (2).

6017-225

9. Pull the frame forwards and refit the pin.

6017-226

10.Grasp the front edge of the cutting unit, pull out and raise into the service position.

If the cylindrical bolt, which is now holding the cutting unit is removed, the cutting unit can be lifted off.

Restoring from service position

To leave the service position, reverse the procedures set out in “Placing in the service position”. Make sure that the cutting unit’s ”lug” (3) enters the loop correctly on the underside of the machine, see diagram.

6017-227

8009-438

38 – English

Page 40

Image 40

Husqvarna Rider 155 manual Restoring from service position, Maintenance, Observe caution to avoid trapping your hand

Contents

Operator´s manual RiderEnglish Svenska – CONTENTS Operator’s Manual for Rider IMPORTANT INFORMATION1. Safety rules for USA Safe operation practices for ride-onmowersI.General operation II.Slope operationIV. Service Travel and transport on public roadsTowing Intended useINTRODUCTION Dear customerTravel and transport on public roads TowingSerial number Good serviceINTRODUCTION EXPLANATION OF SYMBOLS Placards EXPLANATION OF SYMBOLSEnglish 8009-442SAFETY INSTRUCTIONS General useClear the area of objects before mowing Never carry passengersKeep children away from the area to be mowed Personal protective equipmentSAFETY INSTRUCTIONS moving partsBe especially careful when driving on slopes Driving on slopesProceed as follows Mow upwards and downwards on slopes, not sidewaysMaintenance ChildrenNever allow children to operate the machine Never fill the fuel tank indoorsRisk of burn injuries if touched Do not smoke when carrying out maintenanceSAFETY INSTRUCTIONS Transport Never run the machine in an enclosed areamachine SAFETY INSTRUCTIONSPresentation PRESENTATIONLocation of the controls Throttle and Choke lever Speed limiterParking brake PRESENTATIONCutting unit Lift lever for cutting unitLifting of the cutting unit transport position Lowering of the cutting unit cutting positionLever for adjustment of cutting height SeatFuelling PRESENTATIONDRIVING Before startingStarting the engine Cold engineDRIVING Warm engineIMPORTANT INFORMATION Driving the machine DRIVINGCutting tips Mowing patternDRIVING IMPORTANT INFORMATIONRelease lever Stopping the engineDRIVING MAINTENANCE Maintenance scheduleMaintenance interval MaintenanceRemoval of the machine hoods Engine hoodFront hood Right-handfenderAdjusting the brake Checking and adjustment of the steering wiresMAINTENANCE Replacement of the fuel filter Adjusting the throttle wireMAINTENANCE Service of the air filter Never use compressed air to clean the air filtersMAINTENANCE IMPORTANT INFORMATIONBattery Procedures on contact with acidIgnition system External: Rinse well with plenty of waterInspecting the safety system MAINTENANCEMain fuse Checking the tyre pressureCheck the engine’s cooling air intake Air intake grilleObserve caution to avoid trapping your hand Fitting the cutting unitMAINTENANCE Removing the cutting unit MAINTENANCEMAINTENANCE 2. Place the Rider on a flat surfaceChecking the cutting unit’s parallelism Adjusting the parallelism of the cutting unitMAINTENANCE MAINTENANCE Replacing the cutting unit beltIMPORTANT INFORMATION Service position for cutting unit Placing in service positionMAINTENANCE 36 – EnglishMAINTENANCE 7. Engage the strut in the holderMAINTENANCE Restoring from service positionObserve caution to avoid trapping your hand Checking the blades CombiMAINTENANCE IMPORTANT INFORMATIONService position Replacing the break-pinRemoval of BioClip plug Combi Removal of BioClip plugLUBRICATION Check the engine’s oil levelChanging the oil The dip stick must not be screwed downLubricating the belt adjuster Change of oil filterCheck the transmission’s oil level General lubricationProblem TROUBLE SHOOTING SCHEDULEProcedure Service STORAGEWinter storage CoverTECHNICAL DATA DimensionsRider EngineSERVICE JOURNAL Work doneDate, mileage, stamp, sign 46 – EnglishSERVICE JOURNAL Work doneDate, mileage, stamp, sign English –´+H-¶5c¨ SERVICE JOURNALWork done Date, mileage, stamp, signPage ´+H-¶5c¨ 2002W39 114 01