FDD Floppy Connector, IDE1 / IDE2 IDE Connector | Intel GA-G1975X

English

7)FDD (Floppy Connector)

The FDD connector is used to connect the FDD cable while the other end of the cable connects to the FDD drive. The types of FDD drives supported are: 360KB, 720KB, 1.2MB, 1.44MB and 2.88MB. Please connect the red power connector wire to the pin1 position.

3 43 3

21

8)IDE1 / IDE2 (IDE Connector)

An IDE device connects to the computer via an IDE connector. One IDE connector can connect to one IDE cable, and the single IDE cable can then connect to two IDE devices (hard drive or optical drive). If you wish to connect two IDE devices, please set the jumper on one IDE device as Master and the other as Slave (for information on settings, please refer to the instructions located on the IDE device).To ensure that an IDE CD-ROM drive can work properly, please attach it to the IDE 1 connector.

IDE1

4 03 9

2	1
2	40
1	39
	IDE2

GA-G1975X Motherboard

- 24 -

Image 24

Intel GA-G1975X user manual FDD Floppy Connector, IDE1 / IDE2 IDE Connector

Contents

GA-G1975X Motherboard Copyright Product Manual Classification Table of Contents Drivers Installation Item Checklist GA-G1975X Motherboard Layout GA-G1975X Block Diagram Considerations Prior to Installation Installation NoticesInstances of Non-Warranty Preparing Your Computer Feature Summary CPU Bios English Installation of the CPU and Heatsink Installation of the CPUHT functionality requirement content Installation of the Heatsink Installation of Memory Dual Channel Memory Configuration Installation of Expansion Cards Configuring a Multi-Graphics Cards System Configuring a Multi View SystemBefore you begin Configuring an ATi CrossFireTM System Enabling CrossFire Mode I/O Back Panel Introduction Connectors Introduction ATX Power ConnectorATX12V2X4 F11394 / F21394 ATX12V2X4/ATX Power Connector PCIE12V Power Connector 6 Cpufan / Sysfan / Pwrfan Cooler Fan Power Connector FDD Floppy Connector IDE1 / IDE2 IDE Connector SATAII01 / SATAII23 Sata 3Gb/s Connector Battery Fpanel Front Panel Jumper Faudio Front Audio Connector Cdin CD USB1 / FUSB2 / Greenusb Front USB Connector Spdifio Spdif In/Out 16 F11394 / F21394 Ieee 1394 Connector Rfid Pwrled CI Chassis Intrusion, Case Open Coma Coma Connector Surcen Surround Center Connector 22 PW1 / PW2 English English Status Page Setup Menu / Option Page Setup Menu Main Menu Main Menu For example Bios Ver. F1 F12 For Boot Menu „ Standard Cmos Features „ Advanced Bios Features„ Power Management Setup „ PnP/PCI Configuration Time IDE Channel 0 Master, Slave Floppy 3 Mode Support for Japan Area IDE Channel 2/3 MasterDrive a / Drive B Halt on Memory Base MemoryExtended Memory Total Memory Hard Disk Boot Priority Bios Flash ProtectionFirst / Second / Third Boot Device Boot Up Floppy Seek Boot Up Num-LockPassword Check Interrupt Mode Delay For HDD Secs Dram Data Integrity ModeLimit Cpuid Max. to No-Execute Memory Protect Note Pata IDE Set to Sata Port 0/2 Set toSata Port 1/3 Set to OnBoard LAN Boot ROM USB ControllerUSB 2.0 Controller USB Keyboard Support Resume by Alarm Power On By Mouse Power On By Keyboard KB Power on PasswordPCI Latency Timer CLK AC Back Function Current CPU Temperature Current CPU/POWER/SYSTEM FAN Speed RPMPCI 1 IRQ Assignment PCI 2 IRQ Assignment CPU Warning Temperature CPU/POWER/SYSTEM FAN Fail WarningCPU Smart FAN Mode CPU Smart FAN Control MB Intelligent TweakerM.I.T M. NoteCPU Clock Ratio Note Robust Graphics Booster A.2CPU Host Clock Control CPU Host FrequencyMhz Memory Frequency Mhz Dimm OverVoltage ControlPCI-E OverVoltage Control FSB OverVoltage Control Dram RAS# to CAS# Delay Active to Precharge DelayRefresh Mode Select CAS Latency Time Top Performance Select Language Load Fail-Safe Defaults Load Optimized Defaults Set Supervisor/User Password Save & Exit Setup Exit Without Saving English Drivers Installation Install Chipset Drivers Software Applications Driver CD Information Hardware Information Contact Us English Unique Software Utilities EasyTune 5 Introduction User Interface Overview Xpress Recovery2 Introduction How to use the Xpress Recovery2System requirements Main Screen of Xpress Recovery2 PrecautionsLimitations Flash Bios Method Introduction What is Dual Bios Technology?How to use Dual Bios and Q-Flash Utility? Wide Range Protection DisableDefault, Enable Boot From Main BIOSDefault, Backup BiosAuto Recovery EnableDefault, Disable Halt On Error DisableDefault, Enable Method 1 Q-FlashTMUtility Before You Begin Exploring the Q-FlashTM / Dual Bios utility screen Task menu for Dual Bios utilityEntering the Q-FlashTMutility Task menu for Q-Flash utility Using the Q-FlashTMutility Steps You can repeat to Press Y on your keyboard to load defaults Exploring the Q-FlashTMutility screen English Congratulation!! You have updated Bios successfully Bios file becomes F4 after updating Method 2 @BIOSTM Utility Methods and steps English English Installing Sata hard drives in your computer RAID Step Save and exit Bios Setup Configuring RAID set in RAID Bios Create RAID Volume¡G Enter Create Volume Delete RAID Volume Cd bootdrv Menu Making a Sata Driver Disk Installing Sata controller driver during OS installation ENTER=Select F3=Exit Enter= Continue R=Repair F3=Exit Accessing Creative Speaker Settings Channel Speaker Configurations Configuring Multi-Channel Speakers with Audio Combo KitInstalling Audio Combo Kit Front Speaker Out Rear Speaker Out Front Speaker Out Enabling Digital Output English Using Creative Built-in decoder Device Control DTS Introduction English English Using External Decoder Decoding using SoftDVD player Launching DTS Neo6 Settings To launch DTS Neo6 Settings DTS Neo6 Final Word Troubleshooting AMI Bios Beep Codes Post Error Code Post hex Description English E8POST.ASM starts English GA-G1975X Motherboard 108 109 GA-G1975X Motherboard 110 Contact Us Taiwan Headquarters GA-G1975X Motherboard 112