Parallel Port Connector CN7, SubCompact Board | Intel GENE-8310

2.16 Parallel Port Connector (CN7)

	SubCompact Board				G E N E - 8 3 1 0


	9	Ground	10		N/C
COM2/ RS-485 Mode

	Pin	Signal		Pin	Signal
	1	TXD-	2		N/C
	3	TXD+	4		N/C
	5	N/C	6		N/C
	7	N/C	8		N/C
	9	Ground	10		N/C

Note: COM mode, RS-232/422/485, selected by BIOS.

2.16 Parallel Port Connector (CN7)

Pin	Signal	Pin	Signal
1	STBX	2	AFD#
3	PTD0	4	ERR#
5	PTD1	6	PINIT#
7	PTD2	8	SLIN#
9	PTD3	10	Ground
11	PTD4	12	Ground
13	PTD5	14	Ground
15	PTD6	16	Ground
17	PTD7	18	Ground
19	ACK#	20	Ground
21	BUSY	22	Ground
23	PE	24	Ground
25	SLCT	26	N/C

Chapter 2 Quick Installation Guide 2-15

Image 29

Intel GENE-8310 manual Parallel Port Connector CN7, SubCompact Board, G E N E - 8 3 1, Signal

Contents

Intel Celeron M Processor Subcompact Board With LVDS, Ethernet GENE-83106 Channel Audio & Mini PCI SubCompact Board Copyright Notice Acknowledgments Packing List Chapter 1 General Information ContentsChapter 2 Quick Installation Guide Appendix A Programming The Watchdog Timer Chapter 3 Award BIOS SetupChapter 4 Driver Installation I/O Information Appendix BIRQ Mapping Chart I/O Address Map Chapter 1 General Information 1 General InformationChapter 1.1 Introduction Superb Performance and Controllable Power UsageMultiple Display Modes Chapter 1 General Information Wide Expansion Capability 48-bit Dual Channels LVDS TFT LCD 10/100Mbps Fast Ethernet 1.2 FeaturesAC-97 3D Surround 5.1 Channel Audio Supports Type II CompactFlash Memory System 1.3 Specifications Display support Wake-up function Two 5 x 2 Pin Headers Support4 USB 2.0 Ports Does not Part No. 2007831011 Printed in Taiwan JAN Quick Installation GuideChapter 2 Quick Installation Guide 2.1 Safety Precautions The Height of Cooling System Depends on Customer Cooling Device 2.2 Location of Connectors and Jumpers Component Side CFD1 DIMM1 Solder Side Component Side 2.3 Mechanical DrawingThe Height of Cooling System Depends on Customer Cooling Device 103.51 133.93 3.23 8.89 0.00 72.39 0.58 114.300.58 0.00 2.4 List of Jumpers JumpersLabel Function 2.5 List of Connectors Connectors CN17 Closed 2.6 Setting JumpersOpen 2.7 Clear CMOS Selection JP1 2.10 USB2.0 Port 1 Connector CN12.8 LCD Voltage Selection JP2 2.9 COM2 RI/+5V Selection JP5 2.12 Primary IDE Hard Drive Connector CN3 2.11 USB2.0 Port 2 Connector CN2 Name 2.13 Digital IO Connector CN4DIO Address is 801H 2.14 Front Panel CN5 2.15 Serial Port COM2 Connector CN6 2.16 Parallel Port Connector CN7 PinSignal 2.17 Dual Channel LVDS Connector CN82.18 4P Power Connector CN9 2.21 Audio Input/Output Connector CN12 2.19 TV-Out Connector CN102.20 DVI Connector CN11 2.23 External 5VSB/PWRGD Connector CN14 2.22 Ethernet 10/100Base-TX RJ-45 Phone Jack Connector CN132.24 IrDA Connector CN15 G E N E - 8 2.27 Serial Port COM1 Connector CN18 2.25 Fan Connector CN162.26 Mini-DIN PS/2 Connector CN17 2.29 External Battery VBAT2 2.28 CRT Display Connector CN192.30 Mini PCI Slot MPCI1 2.31 CompactFlash Disk Slot CFD1 G E N E - 8 3 1 Chapter 3 Award BIOS Setup Award BIOS Setup 3.1 System Test and Initialization System configuration verification Standard CMOS Features Entering SetupAdvanced BIOS Features Advanced Chipset Features PnP/PCI Configurations Power Management SetupLoad Fail-Safe Defaults Load Optimized Defaults Exit Without Saving Set Supervisor/User PasswordSave and Exit Setup Chapter 4 Driver Installation Driver Installation Follow the sequence below to install the drivers Chapter4 Drivers Installation 4.1 Installation Step 4 - Install Realtek AC97 codec Driver Appendix A Programming the Watchdog Timer A-1 Programming the Watchdog TimerAppendix Appendix A Programming the Watchdog Timer A-2 Configuring Sequence DescriptionA.1 Programming 3 Exit the MB PnP Mode 1 Enter the MB PnP Mode2 Modify the Data of the Registers Appendix A Programming the Watchdog Timer A-4 Configure Control Index=02hWatchDog Timer Configuration Registers WatchDog Timer Configuration Register Index=72h, Default=00h WatchDog Timer Control Register Index=71h, Default=00hWatchDog Timer Time-out Value Register Index=73h, Default=00h Appendix A Programming the Watchdog Timer A-5 A.2 ITE8712 Watchdog Timer Initial Program game port enable mov cl call SetLogicDevice InitialOK CALL ReadConfigurationData CMP AL,87h JNE NotInitial MOV AL,21h RET ExitConfigurationMode ENDP CheckChip PROC NEAR MOV AL,20hCALL ReadConfigurationData CMP AL,12h JNE NotInitial NeedInitial STC RET NotInitial CLC RET CheckChip ENDP ReadConfigurationData PROC NEAR MOV DX,WORD PTR CSCfgPort+06h IN AL,DX RET ReadConfigurationData ENDP Appendix A Programming the Watchdog Timer A-10 END MainSetLogicDevice proc near push ax push cx xchg al,cl mov cl,07h call SuperioSetReg pop cx pop ax ret SetLogicDevice endp Appendix B I/O Information B-1 I/O Information Appendix B I/O Information B-2 B.1 I/O Address MapB.2 1st MB Memory Address Map Appendix B I/O Informaion B-3 B.3 IRQ Mapping ChartB.4 DMA Channel Assignments