List of Connectors | Intel GENE-8310 specification

SubCompact Board	G E N E - 8 3 1 0

2.5 List of Connectors

The board has a number of connectors that allow you to configure your system to suit your application. The table below shows the function of each board's connectors:

Connectors

	Label	Function
	CN1	USB 2.0 Port 1 Connector

	CN2	USB 2.0 Port 2 Connector

	CN3	Primary IDE Hard Drive Connector

	CN4	Digital I/O Connector

	CN5	Front Panel

	CN6	Serial Port COM 2 Connector

	CN7	Parallel Port 1 Connector

	CN8	Dual Channel LVDS Connector

	CN9	4P Power Connector

	CN10	TV-Out Connector

	CN11	DVI Connector

	CN12	Audio Input/Output Connector

	CN13	Ethernet 10/100 Base-TX RJ-45 Phone
		Jack

	CN14	External 5VSB/PWRGD Connector

	CN15	IrDA Connector

	CN16	Fan Connector

Chapter 2 Quick Installation Guide 2-8

Page 22

Image 22

Intel GENE-8310 manual List of Connectors

Contents

6 Channel Audio & Mini PCI GENE-8310Intel Celeron M Processor Subcompact Board With LVDS, Ethernet SubCompact Board Copyright Notice Acknowledgments Packing List Chapter 2 Quick Installation Guide ContentsChapter 1 General Information Chapter 4 Driver Installation Chapter 3 Award BIOS SetupAppendix A Programming The Watchdog Timer IRQ Mapping Chart Appendix BI/O Information I/O Address Map Chapter General InformationChapter 1 General Information 1 Multiple Display Modes Superb Performance and Controllable Power Usage1.1 Introduction Chapter 1 General Information Wide Expansion Capability AC-97 3D Surround 5.1 Channel Audio 1.2 Features48-bit Dual Channels LVDS TFT LCD 10/100Mbps Fast Ethernet Supports Type II CompactFlash Memory 1.3 Specifications System Display 4 USB 2.0 Ports Does not Two 5 x 2 Pin Headers Supportsupport Wake-up function Chapter 2 Quick Installation Guide Quick Installation GuidePart No. 2007831011 Printed in Taiwan JAN 2.1 Safety Precautions 2.2 Location of Connectors and Jumpers Component Side The Height of Cooling System Depends on Customer Cooling Device Solder Side CFD1 DIMM1 The Height of Cooling System Depends on Customer Cooling Device 2.3 Mechanical DrawingComponent Side 103.51 0.58 3.23 8.89 0.00 72.39 0.58 114.30133.93 0.00 Label Jumpers2.4 List of Jumpers Function Connectors 2.5 List of Connectors CN17 Open 2.6 Setting JumpersClosed 2.8 LCD Voltage Selection JP2 2.10 USB2.0 Port 1 Connector CN12.7 Clear CMOS Selection JP1 2.9 COM2 RI/+5V Selection JP5 2.11 USB2.0 Port 2 Connector CN2 2.12 Primary IDE Hard Drive Connector CN3 DIO Address is 801H 2.13 Digital IO Connector CN4Name 2.15 Serial Port COM2 Connector CN6 2.14 Front Panel CN5 2.16 Parallel Port Connector CN7 2.18 4P Power Connector CN9 2.17 Dual Channel LVDS Connector CN8PinSignal 2.20 DVI Connector CN11 2.19 TV-Out Connector CN102.21 Audio Input/Output Connector CN12 2.24 IrDA Connector CN15 2.22 Ethernet 10/100Base-TX RJ-45 Phone Jack Connector CN132.23 External 5VSB/PWRGD Connector CN14 G E N E - 8 2.26 Mini-DIN PS/2 Connector CN17 2.25 Fan Connector CN162.27 Serial Port COM1 Connector CN18 2.30 Mini PCI Slot MPCI1 2.28 CRT Display Connector CN192.29 External Battery VBAT2 2.31 CompactFlash Disk Slot CFD1 SubCompact Board Award BIOS Setup Chapter 3 Award BIOS Setup System configuration verification 3.1 System Test and Initialization Advanced BIOS Features Entering SetupStandard CMOS Features Advanced Chipset Features Load Fail-Safe Defaults Power Management SetupPnP/PCI Configurations Load Optimized Defaults Save and Exit Setup Set Supervisor/User PasswordExit Without Saving Driver Installation Chapter 4 Driver Installation Follow the sequence below to install the drivers 4.1 Installation Chapter4 Drivers Installation Step 4 - Install Realtek AC97 codec Driver Appendix Programming the Watchdog TimerAppendix A Programming the Watchdog Timer A-1 A.1 Programming Configuring Sequence DescriptionAppendix A Programming the Watchdog Timer A-2 2 Modify the Data of the Registers 1 Enter the MB PnP Mode3 Exit the MB PnP Mode WatchDog Timer Configuration Registers Configure Control Index=02hAppendix A Programming the Watchdog Timer A-4 WatchDog Timer Time-out Value Register Index=73h, Default=00h WatchDog Timer Control Register Index=71h, Default=00hWatchDog Timer Configuration Register Index=72h, Default=00h Appendix A Programming the Watchdog Timer A-5 A.2 ITE8712 Watchdog Timer Initial Program game port enable mov cl call SetLogicDevice InitialOK CALL ReadConfigurationData CMP AL,12h JNE NotInitial NeedInitial STC RET ExitConfigurationMode ENDP CheckChip PROC NEAR MOV AL,20hCALL ReadConfigurationData CMP AL,87h JNE NotInitial MOV AL,21h RET NotInitial CLC RET CheckChip ENDP ReadConfigurationData PROC NEAR MOV DX,WORD PTR CSCfgPort+06h IN AL,DX RET ReadConfigurationData ENDP SetLogicDevice proc near push ax push cx xchg al,cl mov cl,07h END MainAppendix A Programming the Watchdog Timer A-10 call SuperioSetReg pop cx pop ax ret SetLogicDevice endp I/O Information Appendix B I/O Information B-1 B.2 1st MB Memory Address Map B.1 I/O Address MapAppendix B I/O Information B-2 B.4 DMA Channel Assignments B.3 IRQ Mapping ChartAppendix B I/O Informaion B-3