Configure Control Index=02h, SubCompact Board

SubCompact Board	G E N E - 8 3 1 0

WatchDog Timer Configuration Registers

Configure Control (Index=02h)

This register is write only. Its values are not sticky; that is to say, a hardware reset will automatically clear the bits, and does not require the software to clear them.

Appendix A Programming the Watchdog Timer A-4

Page 48

Image 48

Intel GENE-8310 Configure Control Index=02h, SubCompact Board, G E N E - 8 3 1, WatchDog Timer Configuration Registers

Contents

GENE-8310 Intel Celeron M Processor Subcompact Board With LVDS, Ethernet6 Channel Audio & Mini PCI SubCompact Board Copyright Notice Acknowledgments Packing List Contents Chapter 2 Quick Installation GuideChapter 1 General Information Chapter 3 Award BIOS Setup Chapter 4 Driver InstallationAppendix A Programming The Watchdog Timer Appendix B I/O InformationIRQ Mapping Chart I/O Address Map General Information ChapterChapter 1 General Information 1 Superb Performance and Controllable Power Usage 1.1 IntroductionMultiple Display Modes Chapter 1 General Information Wide Expansion Capability 1.2 Features 48-bit Dual Channels LVDS TFT LCD 10/100Mbps Fast EthernetAC-97 3D Surround 5.1 Channel Audio Supports Type II CompactFlash Memory 1.3 Specifications System Display Two 5 x 2 Pin Headers Support 4 USB 2.0 Ports Does notsupport Wake-up function Quick Installation Guide Chapter 2 Quick Installation GuidePart No. 2007831011 Printed in Taiwan JAN 2.1 Safety Precautions 2.2 Location of Connectors and Jumpers Component Side The Height of Cooling System Depends on Customer Cooling Device Solder Side CFD1 DIMM1 2.3 Mechanical Drawing Component SideThe Height of Cooling System Depends on Customer Cooling Device 103.51 3.23 8.89 0.00 72.39 0.58 114.30 133.930.58 0.00 Jumpers 2.4 List of JumpersLabel Function Connectors 2.5 List of Connectors CN17 2.6 Setting Jumpers OpenClosed 2.10 USB2.0 Port 1 Connector CN1 2.7 Clear CMOS Selection JP12.8 LCD Voltage Selection JP2 2.9 COM2 RI/+5V Selection JP5 2.11 USB2.0 Port 2 Connector CN2 2.12 Primary IDE Hard Drive Connector CN3 2.13 Digital IO Connector CN4 DIO Address is 801HName 2.15 Serial Port COM2 Connector CN6 2.14 Front Panel CN5 2.16 Parallel Port Connector CN7 2.17 Dual Channel LVDS Connector CN8 2.18 4P Power Connector CN9PinSignal 2.19 TV-Out Connector CN10 2.20 DVI Connector CN112.21 Audio Input/Output Connector CN12 2.22 Ethernet 10/100Base-TX RJ-45 Phone Jack Connector CN13 2.23 External 5VSB/PWRGD Connector CN142.24 IrDA Connector CN15 G E N E - 8 2.25 Fan Connector CN16 2.26 Mini-DIN PS/2 Connector CN172.27 Serial Port COM1 Connector CN18 2.28 CRT Display Connector CN19 2.29 External Battery VBAT22.30 Mini PCI Slot MPCI1 2.31 CompactFlash Disk Slot CFD1 SubCompact Board Award BIOS Setup Chapter 3 Award BIOS Setup System configuration verification 3.1 System Test and Initialization Entering Setup Standard CMOS FeaturesAdvanced BIOS Features Advanced Chipset Features Power Management Setup PnP/PCI ConfigurationsLoad Fail-Safe Defaults Load Optimized Defaults Set Supervisor/User Password Save and Exit SetupExit Without Saving Driver Installation Chapter 4 Driver Installation Follow the sequence below to install the drivers 4.1 Installation Chapter4 Drivers Installation Step 4 - Install Realtek AC97 codec Driver Programming the Watchdog Timer AppendixAppendix A Programming the Watchdog Timer A-1 Configuring Sequence Description A.1 ProgrammingAppendix A Programming the Watchdog Timer A-2 1 Enter the MB PnP Mode 2 Modify the Data of the Registers3 Exit the MB PnP Mode Configure Control Index=02h WatchDog Timer Configuration RegistersAppendix A Programming the Watchdog Timer A-4 WatchDog Timer Control Register Index=71h, Default=00h WatchDog Timer Configuration Register Index=72h, Default=00hWatchDog Timer Time-out Value Register Index=73h, Default=00h Appendix A Programming the Watchdog Timer A-5 A.2 ITE8712 Watchdog Timer Initial Program game port enable mov cl call SetLogicDevice InitialOK RET ExitConfigurationMode ENDP CheckChip PROC NEAR MOV AL,20h CALL ReadConfigurationData CMP AL,87h JNE NotInitial MOV AL,21hCALL ReadConfigurationData CMP AL,12h JNE NotInitial NeedInitial STC RET NotInitial CLC RET CheckChip ENDP ReadConfigurationData PROC NEAR MOV DX,WORD PTR CSCfgPort+06h IN AL,DX RET ReadConfigurationData ENDP END Main Appendix A Programming the Watchdog Timer A-10SetLogicDevice proc near push ax push cx xchg al,cl mov cl,07h call SuperioSetReg pop cx pop ax ret SetLogicDevice endp I/O Information Appendix B I/O Information B-1 B.1 I/O Address Map B.2 1st MB Memory Address MapAppendix B I/O Information B-2 B.3 IRQ Mapping Chart B.4 DMA Channel AssignmentsAppendix B I/O Informaion B-3

Intel GENE-8310 manual Configure Control Index=02h, SubCompact Board, G E N E - 8 3 1

Models: GENE-8310

WatchDog Timer Configuration Registers

Configure Control (Index=02h)

Appendix A Programming the Watchdog Timer A-4