Manuals / Brands / Personal Care / Wheelchair / Invacare / Personal Care / Wheelchair

Invacare II250 SERIES, IIBASIC, IIJR, IISTANDARD - page 35

1 60

Download 60 pages, 2.62 Mb

35

Battery Tray

Hex Bolt

FIGURE 2 - REPLACING BATTERY BOX RET AINING

STRAP - ALL FWD MODELS EXCEPT RANGER IIJR

All FWD Models Except RANGER IIJR

(FIGURE 2)

1. If necessary, remove the front and rear shrouds. Refer

to REMOVING/INSTALLING SHROUDS in PROCE-

DURE 9 of this manual.

2. Remove the battery boxes from the wheelchair. Refer

INSTALLING/REMOVING BATTERY BOXES in

PROCEDURE 11 of this manual.

3. Remove the two (2) hex bolts and locknut that se-

cure the existing battery tray to the tray support.

4. Remove the existing battery tray from the wheelchair.

5. Position the new battery tray on the tray support as

shown in FIGURE 2.

6. Secure the new battery tray to the tray support with

the two (2) hex bolts and locknuts. Tighten securely.

7. Reinstall the battery boxes. Refer to INSTALLING/

REMOVING BATTERY BOXES in PROCEDURE 11

of this manual.

8. If necessary, install the front and rear shrouds. Refer

to REMOVING/INSTALLING SHROUDS in PROCE-

DURE 9 of this manual.

Tray Support

Locknut

R

E

T

A

I

N

I

N

G

S

T

R

A

P

PROCEDURE 7RETAINING STRAP

Contents

Main WARNING SPECIAL NOTES TABLE OF CONTENTS TABLE OF CONTENTS LIMITED WARRANTY............... BACK COVER PROCEDURE 2 - SAFETY INSPECTION CHECKLIST/TROUBLESHOOTING .............18 PROCEDURE 3 - FRONT RIGGINGS ...........21 PROCEDURE 4 - ARMS............................... 27 SPECIFICATIONS P NOTE: Refer to PERCENTAGE OF WEIGHT DISTRIBUTION in PROCEDURE 1 of this manual. v PERFORMANCE RANGER IIBASIC RANGER II250 SERIES RANGER IISTANDARD SPECIFICATIONS NOTE: Refer to PERCENTAGE OF WEIGHT DISTRIBUTION in PROCEDURE 1 of this manual. v PERFORMANCE RANGER IIBASIC RANGER II250 SERIES RANGER IISTANDARD Page GENERAL WARNINGS GENERAL GUIDELINESPROCEDURE 1 GENERAL WARNINGS (CONTINUED) SAFETY/HANDLING OF WHEELCHAIRS ESCALATORS? SORRY! GENERAL GUIDELINESPROCEDURE 1 *NOTE: 14 wide is only for RANGER II . Page Page WARNING/CAUTION LABEL LOCATION - MWD MODELS (RANGER IIBASIC/RANGER IISTANDARD /RANGER II250 SERIES) Crossbrace Push Bracket Crossbrace WARNING/CAUTION LABEL LOCATION - FWD MODELS (RANGER IIBASIC/RANGER IISTANDARD/RANGER II250 SERIES) Motor Assembly Controller (Back View) NOTE: Caution Label is located on side shroud. WARNING/CAUTION LABEL LOCATION - FWD MODELS (RANGER IIJR) Motor Assembly Controller (Back View) Battery Tray BATTERY BOX SHIPPING INSERTS REMOVING BATTERY BOX SHIPPING INSERTS (RANGER II SAFETY INSPECTION/TROUBLESHOOTINGPROCEDURE 2 DONT DO TROUBLESHOOTING - MECHANICAL CHECKING BATTERY CHARGE LEVEL NOTE: Perform this procedure when a digital voltmeter is not available. NOTE: DO NOT fill hydrometer more than 3/4 full. Number of Floating Balls Will Vary According to Charge SAFETY INSPECTION/TROUBLESHOOTING PROCEDURE 2 PROCEDURE 2 SAFETY INSPECTION/TROUBLESHOOTING SAFETY INSPECTION CHECKLIST ADJUSTING FOOTREST HEIGHT FOOTRESTS (FIGURE 1) ELEVATING LEGRESTS (FIGURE 5) REPLACING HEEL LOOPS (FIGURE 4) RAISING/LOWERING ELEVATING LEGRESTS AND/OR ADJUSTING CALFPADS (FIGURE 6) ADJUSTING/REPLACING TELESCOPING FRONT RIGGING SUPPORT (FIGURE 7) ADJUSTING REMOVABLE FOOTBOARD ADJUSTING THE REMOVABLE FOOTBOARD HEIGHT (FIGURE 11) PREPARING REMOVABLE FOOTBOARD FOR WHEELCHAIR TRANSPORTATION (FIGURE 12) INSTALLING/REMOVING FLIP BACK ARMRESTS (FIGURE 1) ADJUSTING FLIP BACK ARMRESTS (FIGURE 2) PROCEDURE 4ARMS ADJUSTING CAPTAIN'S SEAT ARMRESTS ARMSPROCEDURE 4 Armrest Socket Screw Armrest ADJUSTING CAPTAIN'S SEAT (FIGURE 2) REPLACING SEAT UPHOLSTERY (FIGURE 1) REMOVING/INSTALLING CAPTAIN'S SEAT (FIGURE 3) REPLACING SEAT POSITIONING STRAP PREPARING MKIV JOYSTICK FOR USE (FIGURE 1) REPOSITIONING MKIV JOYSTICK PROCEDURE 6ELECTRONICS DISCONNECTING/CONNECTING LIMIT SWITCH (FIGURE 3) PROCEDURE 6 ELECTRONICS REPOSITIONING BATTERY CHARGER CONNECTOR (FIGURE 4) FUSE REPLACEMENT REPLACING BATTERY BOX RETAINING STRAP Page PROCEDURE 8 WHEELS ENGAGING/DISENGAGING MOTORS WITH CLUTCHES (FIGURES 1 AND 2) Front of Wheelchair ENGAGING/DISENGAGING MOTORS WITH MOTOR LOCKS Outside of Wheelchair ADJUSTING FORKS (FIGURE 4) PROCEDURE 8WHEELS REMOVING/INSTALLING SHROUDS Page U PROCEDURE 9 SHROUDS Page BATTERIES INTO/FROM BATTERY BOXES (FIGURE 1) PROCEDURE 10BATTERIES CONNECTING BATTERY CABLES DIRECT MOUNT METHOD (FIGURE 2, 3 AND 4). NOTE: It will be necessary to trim excess tie-wrap in order to install the battery box top(s). Page Battery Cable Battery Clamp Cover NEGATIVE (-) Battery Terminal/Post and Battery Clamp POSITIVE (+) Battery Terminal/Post (Note position of battery clamp) PROCEDURE 10BATTERIES Page TRANSPORTING RANGER II FWD Seat Rails Seat Rails Push Brackets WHEN TO CHARGE BATTERIES Battery Gauge Display (BGD) Battery Discharge Indicator (BDI) CHARGING BATTERIES (FIGURE 4) REPLACING BATTERIES *NOTE: RANGER II NOTE: When done, these areas should be shiny, not dull. INSTALLING/REMOVING BATTERY BOXES Page BATTERY TRAY Page TRANSPORTING RANGER II - MWD Battery Gauge Display (BGD) Crossbraces Battery Discharge Indicator (BDI) WHEN TO CHARGE BATTERIES CHARGING BATTERIES (FIGURE 4) PROCEDURE 12 MWD WHEELCHAIRS REPLACING BATTERIES PROCEDURE 12MWD WHEELCHAIRS PROCEDURE 12 MWD WHEELCHAIRS INSTALLING/REMOVING BATTERY BOXES (FIGURE 5) BATTERY TRAY (FIGURE 7) ADJUSTING THE STABILIZER (FIGURE 6) LIMITED WARRANTY