Fuse Replacement Figure, Electronics, Fuse Holder | Invacare R2-250

ELECTRONICS

PROCEDURE 6

REPOSITIONING BATTERY CHARGER CONNECTOR (FIGURE 3)

NOTE: This procedure applies to wheelchairs equipped with the Mark IV controller ONLY.

1.Remove the hex bolt from the T-nut that secures the battery charger connector bracket to the wheelchair.

2.Remove the battery charger connector bracket/ battery charger connector.

3.Slide the T-nut out from the channel on the base frame of the wheelchair.

4.Reposition the T-nut in the channel on the oppo- site side of the wheelchair.

5.Install the hex bolt through the battery charger con- nector bracket AND into the T-nut. Securely tighten.

Hex Bolt

Battery Charger Connector

Battery Charger

Connector Bracket

T-Nut

Channel

Base Frame

NOTE: Base frame shown is for reference ONLY. It is NOT a true representation of the Pronto base frame.

FIGURE 3 - REPOSITIONING BATTERY CHARGER

CONNECTOR

FUSE REPLACEMENT (FIGURE 4)

NOTE: This procedure applies to wheelchairs equipped with the Mark IV controller ONLY.

1.Remove the front shroud. Refer to REMOVING/IN- STALLING THE SHROUDS in PROCEDURE 9 of this manual.

2.Remove the front battery. Refer to REMOVING/IN- STALLING THE BATTERIES in PROCEDURE 11 of this manual.

3.Grasp and pull the existing fuse to remove it from fuse holder.

4.Install new fuse.

5.Reassemble wheelchair by reversing STEPS 1-2.

Fuse

Fuse

Holder

E L E C T R O N I C S

FIGURE 4 - FUSE REPLACEMENT

31

Image 31

Invacare R2-250 Fuse Replacement Figure, Repositioning Battery Charger Connector Figure, Electronics, E C T R O N I C S

Contents

ProntoR2/Pronto R2-250 Series Wheelchair TIE-DOWN Restraints and Seat Positioning Straps R N I N G Table of Contents Performance Specification SWeight limitation varies with motor. Refer to Rain and operators weight General Guidelines Procedure General Guidelines Procedure General Guidelines Remove the occupant from the wheelchair SAFETY/HANDLING WheelchairsStability and Balance Stairways Reaching, Leaning, Bending and Bending Forward Shift body weight into seat with transferMinimize GAP Distance Functional Reach From a Wheelchair Reaching, Bending Backward Shipping Insert Battery Box Shipping Insert InstalledShipping Insert Removed Safety INSPECTION/TROUBLESHOOTING Safety Inspection Checklist Safety INSPECTION/TROUBLESHOOTINGPROCEDURE Troubleshooting MechanicalTroubleshooting Electrical Checking Battery Charge Level Number of Floating Balls Using Hydrometer to Check Battery Cells Lead Acid FigureNumber of Floating Balls Will Vary According to Charge O N T INSTALLING/REMOVING Footrests FigureAdjusting Footrest Height Front Riggings O N T I N G S INSTALLING/REMOVING Elevating Legrests FigureProcedure Front Riggings Replacing Heel Loops Figure Replacing Adjusting CalfpadsAdjusting Raising/Lowering Elevating Legrests Height Figure Adjusting Removable FootboardDepth Figure Angle Figure Removing The Removable Footboard Plate Installing The Removable Footboard Plate Removing the One Piece Footboard INSTALLING/REMOVING the ONE Piece Footboard FigureAdjusting the ONE Piece Footboard HEIGHT, ANGLE, and Depth Installing the One Piece Footboard Flat Head Screws Heel Mounting Holes Footboard REMOVING/INSTALLING the CALF-PADS FigureAdjusting the CALF-PADS Adjusting the Calf-Pad Height Figure Hub Cap Adjusting the Calf-Pad Width FigureAdjusting the Calf Pad Angle Figure Locknut Caplug Washer Remove the two 2 hub caps from the pivot bracket Adjusting the Calf-Pad Depth Calf-Pad Bracket Locknuts Pivot Calf-Pad Legrest TubeNylon Small Washers O N T I N G Footrest Angle Adjustments Figure M S INSTALLING/REMOVING Flip Back Armrests FigureAdjusting Flip Back Armrests Figure Arms Positioning Flip Back Armrests for Use Adjusting Captains Seat ArmrestsProcedure Arms Adjust top of the flip back armrest to the desired height P T a I N S Adjusting Captains Seat FigureReplacing Seat Positioning Strap Captains SEAT/POSITIONING Strap E C Adjustable Seat Back Angle/Recliner Seat Models FigureRepositioning Mkiv Joystick Preparing Mkiv Joystick for USE Figure E C T R O N I C S Fuse Replacement FigureRepositioning Battery Charger Connector Figure Electronics Retaining Strap Replacing Battery BOX Retaining Strap FigureT a R a P Outside of Wheelchair Front of Wheelchair ENGAGING/DISENGAGINGMOTORS with Clutches Figures 1ENGAGING/DISENGAGING Motors with Motor Locks Figure Wheels Additional Adjustments for User Preference Detail B Adjusting Forks Figure Adjusting the Stabilizer FigureWheels Shrouds REMOVING/INSTALLING Shrouds FigureR O U D S Recliner Recliner Operation FigureReplacing Back or Headrest Upholstery Figure C L I N E R Cane Upholstery Adjusting Back or Headrest Upholstery FigureRecliner Headrest Upholstery Extension Batteries T T E R I E S Dual U1 Batteries Connecting Battery CablesBatteries Direct Mount Method Connect Battery Cable to Battery Terminal AS Shown Connect Battery Cables Ring Terminals to This Side Posts Installing Battery Clamp Covers Black battery clamp cover onto Black bat- tery cableInstall the battery box tops Detail a Connecting Battery Cables to Batteryies TERMINALS/POSTSRED Battery Clamp Cover Negative Battery Terminal/Post Tie-Wrap Group 22NF Battery Mkiv RII Joystick When to Charge Batteries FigureDescription and Use of Battery Chargers Charging Batteries Figure Detail a Required ItemsDetail B Replacing Batteries INSTALLING/REMOVING Battery Boxes FigureRecommended Battery Types Cleaning Battery Terminals Strap Clip One 1 Connector Battery BoxRear of Chair Retaining Front R R a N T Y Warranty USA