Manuals / Invacare / Personal Care / Wheelchair

Invacare Transformer All Sport Replacing Screw-On Seat Upholstery, Fastening Flaps, Top Crossbar

Models: Terminator BB

1 76

Page 59

SECTION 6—SEAT

Fastening Flaps
Adjuster Straps (Rear)	Seat	Anchor Loop
Adjuster Straps (Rear)	Upholstery
		Wheelchair Frame
Top Crossbar		(Top Bar)
Top Crossbar

FIGURE 6.1 Replacing Adjustable Tension Seat Upholstery

Replacing Screw-On Seat Upholstery

NOTE: For this procedure, refer to FIGURE 6.2.

1.Remove the seat cushion from the wheelchair.

2.Remove the twelve mounting screws that secure the existing seat upholstery to the seat frame.

3.Remove the existing seat upholstery.

Mounting

Screws

Seat

Upholstery

Seat Frame

FIGURE 6.2 Replacing Screw-On Seat Upholstery

Part No 1114851

Everyday and Sport Series Wheelchairs

Page 59

Image 59

Invacare Transformer All Sport, 1114851 Replacing Screw-On Seat Upholstery, 1 Replacing Adjustable Tension Seat Upholstery

Contents

Top End Sports Series Owner’s Operator and Maintenance ManualEveryday and Sport Series Wheelchairs Top End Everyday SeriesEveryday and Sport Series Wheelchairs REGISTER YOUR PRODUCT TABLE OF CONTENTSTABLE OF CONTENTS SECTION 3-SAFETY INSPECTIONTABLE OF CONTENTS SECTION 5-WHEELSSECTION 6-SEAT TABLE OF CONTENTSAll Wheelchairs with Swivel Anti-tip Except LIMITED WARRANTYSECTION 7-FOOTREST ANTI-TIPPERor Complete and mail the form on the next page REGISTER YOUR PRODUCThere Cut Along LineCity State/Province FoldEveryday and Sport Series Wheelchairs Fold here Cut Along Line Fold hereInvacare Product Registration Form Please Seal with Tape Before MailingWHEELCHAIR TIE-DOWN RESTRAINTS AND SEAT POSITIONING STRAPS SPECIAL NOTESTERMINATOR NOTE All specifications are approximateTYPICAL PRODUCT PARAMETERS TYPICAL PRODUCT PARAMETERSEVERYDAY ED TERMINATOR TITANIUMNOTE All specifications are approximate TYPICAL PRODUCT PARAMETERSTYPICAL PRODUCT PARAMETERS TITANIUMAND QUAD RUGBY NOTE All specifications are approximateT-5 TENNIS ELITE NOTE All specifications are approximateTYPICAL PRODUCT PARAMETERS PAUL SCHULTE SIGNATURE BBTRANSFORMER ALL-SPORT NOTE All specifications are approximateTYPICAL PRODUCT PARAMETERS Operating Information SECTION 1-GENERAL GUIDELINESStability Warning DO NOT tip the wheelchair without assistance Tire Pressure and Information Weight TrainingWeight Limitation Stability and Balance SECTION 2-SAFE HANDLINGA Note to Wheelchair Assistants Percentage of Weight DistributionCoping with Everyday Obstacles Rear of Center ofWheelchair Gravity Reaching, Leaning and Bending - ForwardReaching, Leaning - Backwards DO NOT tip the wheelchair without assistance TippingTipping - Curbs Stairways Transferring To and From Other Seats Inspect Initially SECTION 3-SAFETY INSPECTIONSafety Inspection Checklist SECTION 3-SAFETY INSPECTION Inspect/Adjust WeeklyInspect/Adjust Monthly Inspect/Adjust Periodically TroubleshootingSuggested Maintenance Procedures MaintenanceMaintenance Safety Precautions 10. Check upholstery for sagging, rips or tears SECTION 4-BACK Back Angle AdjustmentBack MUST be locked securely in place before using the wheelchair NOTE For this procedure, refer to FIGURE3. Adjust back canes to back angle required NOTE For this procedure, refer to FIGURE Removing/Installing Foldover Back UpholsteryInstalling Foldover Back Upholstery Removing Foldover Back UpholsteryThe Back Upholstery Cover Adjustable Tension Back UpholsteryThe Adjustable Tension Straps Replacing Adjustable Tension Back UpholsteryPush pin MUST be protruding through hole in back cane Back Height Adjustment Adjustable Backs OnlyNOTE Both back canes should be adjusted to the same height NOTE Observe the tautness of the back upholstery for reinstallation3. Reinstall the fastening flaps onto the back canes NOTE The fastening flap with logo is for the left back caneNOTE Right and left is determined by sitting in the wheelchair NOTE For this procedure, refer to FIGURE Removing/Installing Rear WheelsKeep locking pins clean SECTION 5-WHEELSNOTE End of Quick Release Adjusting Quick-Release Axlesis not visible when inserted into camber bar Replacing Quad-Release AxlesNOTE For this procedure, refer to FIGURE Adjusting Quad-Release HandlesIn and/or Out Removing Play from Rear WheelsNOTE For this procedure, refer to FIGURE Handrim ReplacementRepairing/Replacing Rear Wheel, Tire/Tube NOTE For this procedure, refer to FIGURE Opening/Closing Camber ClampsSocket Screw Camber Clamp FIGURE 5.6 Opening/Closing Camber ClampsSECTION 5-WHEELS Camber Clamp Closed Position Quick ReleaseOpen Position LeverNOTE For this procedure, refer to FIGURE Adjusting Rear Wheel CamberCamber Tube A4 Camber SystemNOTE For this procedure, refer to FIGURE Determining Toe In/Toe OutFront of Wheelchair 12-inches Rear of Wheelchair Adjusting Toe In/Toe OutNOTE For this procedure, refer to FIGURE Camber TubeNOTE For this procedure, refer to FIGURE Course AdjustmentNOTE Make the following adjustment for one camber at a time NOTE Rear wheels are removed from theSECTION 5-WHEELS Fine AdjustmentNOTE For this procedure, refer to FIGURE drawings for clarity, there is no need to remove Adjusting Wheelbase Length Adjusting Center of Gravityadjustment how the adjustment rings can be positionedLengthening Non-Suspension - Top ViewHex Screw RemoveNOTE For this procedure, refer to FIGURE Adjusting Wheelbase WidthNOTE The wheelbase width can be increased/decreased by 1‐inch NOTE For this procedure, refer to FIGUREIndexing Replacing Axle TubeNOTE For this procedure, refer to FIGURE 15. Adjust the axle tube. Refer to Adjusting the Axle Tube on page NOTE DO NOT close the camber clamps at this timeNOTE Stand behind the wheelchair to determine left or right Adjusting the Axle TubeA4 Camber System NOTE For this procedure, refer to FIGURENOTE For this procedure, refer to FIGURE Camber Tube11. Repeat STEP NOTE For this procedure, refer to FIGURE Replacing/Adjusting CastersNOTE When changing a rear wheel/front Adjusting Front Caster Heightbefore performing this procedure NOTE For this procedure, refer toNOTE For this procedure, refer to FIGURE Wheel Lock Adjustment/ReplacementWheel Lock Adjustment FIGURE 5.20 Wheel Lock Adjustment/ReplacementNOTE Rear wheel not shown for clarity NOTE High mount wheel lock shown for clarityNOTE Right and left is determined by sitting in the wheelchair Replacing Adjustable Tension Seat UpholsterySECTION 6-SEAT NOTE For this procedure, refer to FIGURENOTE For this procedure, refer to FIGURE FIGURE 6.1 Replacing Adjustable Tension Seat UpholsteryReplacing Screw-On Seat Upholstery FIGURE 6.2 Replacing Screw-On Seat UpholsteryNOTE The footrest tubing will slide once the hardware is removed Adjusting Transformer Seat HeightAdjusting Front Seat Height Adjusting Rear Seat HeightSECTION 6-SEAT FIGURE 6.3 Adjusting Transformer Seat HeightAdjustment Holes Coved Washer Adjustment ScrewAdjusting/Replacing Standard Footrest Adjusting the FootrestSECTION 7-FOOTREST ANTI-TIPPER Replacing the FootrestAdjusting Installing/Adjusting Optional Clamp on Raised FootrestReplacing/Adjusting Optional A4 Footrest InstallingNOTE Observe the angle of footplate for reinstallation Installing the X-Terminator FootrestAdjusting Footplate Angle Adjusting Footplate DepthAngle Adjusting the X-terminator and Transformer FootrestsNOTE For this procedure, refer to FIGURE 7.4 and FIGURE DepthNOTE For this procedure, refer to FIGURE Adjusting/Replacing Anti-tipperEnsure both anti-tippers are adjusted to the same height Replacing Anti-tipper Adjusting Anti-tipperNOTE This applies to any Terminator ordered with swivel anti‐tip Installing/Removing/Adjusting Swivel Anti-TipInstalling/Depth Adjustment RemovingNOTE View Adjusting HeightNOTE For this procedure, refer to FIGURE 7.2, Detail A Paul Schulte Signature BB and T-5 Tennis Elite Models ONLYNOTE For this procedure, refer to FIGURE SECTION 8-SUSPENSIONElastomers and Suspension Replacing Rear ElastomersNOTE For this procedure, refer to FIGURE Replacing Front ElastomersNOTE One mounting screw will not turn Lower Portion of Fork Elstaomer Mounting Screw Threaded Sleeve FIGURE 8.2 Replacing Front ElastomersSECTION 8-SUSPENSION Upper Portion of Fork Mounting Screw Use LoctiteInstalling Installing/Removing the Wing/BumperNOTE The following procedures are for Transformer wheelchairs ONLY SECTION 9-WING/BUMPEREveryday and Sport Series Wheelchairs SECTION 9-WING/BUMPERLIMITED WARRANTY LIMITED WARRANTYCanada

Fastening Flaps

Adjuster Straps (Rear)

Top Crossbar

FIGURE 6.1 Replacing Adjustable Tension Seat Upholstery

Replacing Screw-On Seat Upholstery

Mounting

FIGURE 6.2 Replacing Screw-On Seat Upholstery