Manuals / Brands / Photography / Camcorder / JAI / Photography / Camcorder

JAI TM-1020 2.2.7 Power Supplies and Power Cable Setup

1 52

Download 52 pages, 1.49 Mb

Page 13

TM-1020 Series Progressive Scan Shutter Cameras

Installation

2.2.7 Power Supplies and Power Cable Setup

2.2.7 (a) Power Supplies

The TM-1020 series camera requires 12V DC power that is obtained through the 12-pin connector

located on the rear panel of the camera. JAI, Inc. recommends the following power supplies:

PD-12UU 100-240V AC/12V DC 1.2A universal voltage power supply,

(No 12-pin connector) US Plug

PD-12UUP PD-12UU with12-pin connector US plug

PD-12UE PD-12UU European plug

(No 12-pin connector)

PD-12UEP PD-12UU with 12-pin connector European plug

For users providing power through the 12-pin connector, the PD-12P, PD-12UEP and PD-12UUP

power supplies are available with the 12-pin mating connector already attached to the leads from the

power supply. The PD-12UU and PD-12UE power supplies can be connected to the JAI, Inc. power

cable via a terminal strip or directly.

When wiring the PD-12UU and PD-12UE power supplies directly, please note the following:

•The lead ends must be twisted together and tin-soldered for strength and electrical continuity.

•Shrink tubing or a similar insulator should be used to prevent exposed leads from touching and

shorting.

•The +12V lead is marked with a red stripe or white lettering; be sure not to reverse the leads.

•All connections must be properly insulated to prevent shorting.

2.2.7 (b) JAI, Inc. Power Cables

If you are using JAI, Inc. power cables such as the 12P-02S, please refer to the 12-pin connector pin-out

diagram in “12-Pin Connector (LVDS/RS-422 version)” on page6. The cable pin-out diagram is shown

in Figure 8 below. The color-coded leads use Gray for Ground and Yellow for +12V.

Contents

Main Page Page iii Notice Warra nty Certifications WARNING UL Page 2 Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 3 Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16 6 Appendix. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38 Page vii List of Tables Page Page ix List of Figures Page TM-1020 Series Progressive Scan Shutter Cameras Operation Manual 1 Introduction 1.1 Product Description 1.2 Features 1.3 Functional Option Page 4 Introduction 1.4 System Configuration Figure2 below presents a typical system confi guration for the Camera Link version. FIGURE 1. TM-1020 Series System Configuration Figure1 below presents a typical system configuration for the LVDS/RS-422 version. FIGURE 2. CL (Camera Link) System Configuration 2 Installation 2.1 Getting Started 2.1.1 Unpacking Instructions 2.1.2 Components List 2.1.3 Accessories and Options 2.2 Camera Setup 2.2.1 Heat Dissipation 2.2.2 Connector Pin Configurations Page 7 Page 8 Page 9 Page 10 TM-1020 Series Progressive Scan Shutter Cameras 2.2.3 Shutter Speed Control Dial (LVDS/RS-422 version) 2.2.4 RS-232 Communication Cable (LVDS/RS-422 version) Page 11 Installation 2.2.5 Digital Output Cable (LVDS/RS-422 version) FIGURE 6. Pin-out Configuration for Digital Output Cable FIGURE 5. Digital Output Cable 30DG-02 Female Male 2.2.6 Camera Link Cable (CL Versions Only) 2.2.7 Power Supplies and Power Cable Setup Page 14 } 2.2.8 Attaching the Analog Video Output Page Page 16 3Operation 3.1 Camera Rear Panel (LVDS/RS-422 Version) 3.1.1 Up/Down Switch 3.1.2 Digital Output Connector 3.1.3 Analog Output Connector 3.1.6 Mode Selection Switch Page Page 19 3.4 Electronic Shutter 3.5 Integration 3.6 Asynchronous Reset Page 21 3.6.1 Internal Shutter Speed Control (TM-1020 Series) Page 22 Page 23 3.6.3 Internal Shutter Speed with Fast Mode (TM-1020-15 only) Page 24 3.6.4 Internal Shutter Speed with Slow Mode (TM-1020-15 Only) Page 25 3.6.5 External VINIT with Pulse Width (TM-1020-15 Only) Page 26 3.7 Dynamic Range Control 3.7.1 Programmable Look-Up Table (LUT) and Knee Control Page 27 FIGURE 15. Look-Up Table Progressive scan 3.8 Scan Modes The TM-1020 series supports the following scan modes: 256 224 192 160 128 96 64 32 0128 256 384 512 640 768 896 1024 line 1 line 2 n n+1 line 1+2 line 3+4 (2n-1)+2n 3.8.1 Full Progressive Scan 3.8.2 Two-Row Binning 3.9 External Sync and Pixel Locking Page 29 3.10 Camera Timing Charts 1. Pixel Clock and Digital Data Tcd = 19.00 nsec, Tdc = 31.00 nsec, Thd = 11.00 nsec. 2. Horizontal Signals Page 30 3. External Reset Timing 4. Async Reset Timing Horizontal Frequency: 15.748 KHz 1H = 63.50 sec Page 31 Page 32 K [3 H], (97 ns) 4. Async Shutter 0 Reset Timing Horizontal Frequency: 31.50 KHz 1H = 31.75 sec 3.11 Serial Communication Kit Page 34 4 LVDS-Version Camera RS-232 Commands Page 35 5 Troubleshooting 5.1 Problems and Solutions 5.1.1 Symptom: No Video 5.1.2 Symptom: Dark Video 5.1.3 Symptom: Non-synchronized Video 5.2 Information and Support Resources Page 38 6 Appendix 6.1 Specifications Page Page 40 Appendix 6.1.1 TM-1020 Series Physical Dimensions FIGURE 17. Physical Dimensions Rear Panel for standard camera TM-1020 series camera Page 41 6.1.2 TM-1020 CL Series Physical Dimensions FIGURE 19. Spectral Response FIGURE 18. CL Version Physical Dimensions 6.1.3 Spectral Response <