If in Doubt Consult a Competent Electrician | JVC CA-WMD90R specification

Warnings, Cautions and Others

IMPORTANT for the U.K.

DO NOT cut off the mains plug from this equipment. If the plug fitted is not suitable for the power points in your home or the cable is too short to reach a power point, then obtain an appropriate safety approved extension lead or consult your dealer.

BE SURE to replace the fuse only with an identical approved type, as originally fitted.

If nontheless the mains plug is cut off ensure to remove the fuse and dispose of the plug immediately, to avoid a possible shock hazard by inadvertent connection to the mains supply.

If this product is not supplied fitted with a mains plug then follow the instructions given below:

IMPORTANT:

DO NOT make any connection to the terminal which is marked with the letter E or by the safety earth symbol or coloured green or green-and-yellow.

The wires in the mains lead on this product are coloured in accordance with the following code:

Blue : Neutral

Brown : Live

As these colours may not correspond with the coloured markings identifying the terminals in your plug proceed as follows:

The wire which is coloured blue must be connected to the terminal which is marked with the letter N or coloured black.

The wire which is coloured brown must be connected to the terminal which is marked with the letter L or coloured red.

IF IN DOUBT - CONSULT A COMPETENT ELECTRICIAN.

Caution –– switch!

Disconnect the mains plug to shut the power off completely.

The switch in any position does not disconnect the mains line.

The power can be remote controlled.

CAUTION

To reduce the risk of electrical shocks, fire, etc.:

1.Do not remove screws, covers or cabinet.

2.Do not expose this appliance to rain or moisture.

– G-1 –

Image 2

JVC CA-WMD90R manual If in Doubt Consult a Competent Electrician

Contents

CA-WMD90R If in Doubt Consult a Competent Electrician Class Laser Product Precautions Introduction Contents Become familiar with the buttons and controls on your unit Location of the Buttons and ControlsDisplay Window MD deck a section Front PanelAmplifier/tuner section MD deck B section Remote Control Remote Control Getting Started Putting the Batteries into the Remote ControlConnecting Antennas Unpacking AM antenna Connecting SpeakersYou can connect the speakers using the speaker cords To connect an outdoor AM antenna Connecting Other Equipment To connect a cassette deck Output terminal To start the display demonstration manually Front panel Remote control Basic and Common Operations Adjusting the Volume Setting the ClockTurning On the Power and Selecting the Sources To adjust the clock again Reinforcing the Bass Sound Creating Your Own Sound Mode Manual ModeTo use your own sound mode Activating the Surround Effect Listening to FM and AM MW/LW Broadcasts To change the FM reception mode Tuning in a StationPresetting Stations Changing the RDS Information Tuning in a Preset StationReceiving FM Stations with RDS Searching for Programs by PTY Codes PTY Search Switching to a Program Type of Your Choice TemporarilyAlarm Òback to the beginning PTY Select flashes in the main display More about the EON function Alarm functionTest function Description of the PTY codes R. M Playing Back CDs Basic CD Operations Loading CDsPlaying Back the Entire Discs Continuous Play To exchange CDs during playback of another Programming the Playing Order of the Tracks Program Play To go to another track directly using the number buttonsTo check the program contents To go to another track Prohibiting Disc Ejection Disc Lock Playing at Random Random PlayRepeating Tracks or CDs Repeat Play Tracks of all loaded CDs will play at random Cancel Playing Back MDs Loading MDs When using MD deck aWhen using MD deck B Playing Back the Entire MD Continuous Play While playing an MD, you can do the following operations Basic MD OperationsTo change the display Indications Insert an MD Tracks are played in the order you have programed Press #/ 8 on MD deck B or MD B 6 on the remote control Insert MDs Tracks of the loaded MDs will play at random Repeating Tracks Repeat PlayTo prohibit disc ejection Disc Lock Recording on MDs FM/AM Tape AUX To avoid erasing important recordings Before You Start RecordingAbout the track marks Recording is only possible on MD deck B To check the remaining time When recording from the cassette deck, start playing a tapeRecording the External AUX Equipment AUX Recording Press AUX again MD to MD Synchronized Recording Various Recording FunctionsSynchronized Recording Start playing the source on the external equipment Press Start Enter To confirm the recording contentsCD to MD Synchronized Recording On the unit only Load a CD On the unit only Load CDs Single Track RecordingFirst Track Recording Rotate the left jog dial to select the recordable MD Repeat to program other tracks Listening Edit RecordingOn the unit only Prepare a CD or an MD as the source sound To stop any time during editing process and start Triple Recording Long REC lamp also lights Long RecordingPrepare the source you want to record from Recording starts from MD 1, MD 2 to MD Editing MDs Introducing MD Editing Functions To join the divided tracks again, see the Join function Divide FunctionPress MD Edit To divide the joined tracks, see the Divide function Join FunctionMove Function Rotate the right jog dial until Move ? appears Press SET Edit CANCEL, then select the correct track number againErase Function MD deck B starts playing the MD ALL Erase Function Assigning Titles to MDs TUV Assigning a Title Using the Unit You can make a correction or change the title Changing the TitlePress Enter Start to finish the current title entry Make sure that the character you want to change is flashing Press the button for the next character you want to input Track title entry indication mode appears whenPress MD Title Input Press Enter to finish the current title entry Name Using the Timers Sleep To turn on or off Recording Timer after its setting is done Using Recording TimerHow Recording Timer actually works To turn on the Recording Timer, press SET Volume level will be set to 20 loud Using Daily TimerHow Daily Timer actually works Volume level will be set the previous level when How Sleep Timer actually works Timer PriorityUsing Sleep Timer General Notes MaintenanceTo clean the CD Handling CDs MD Disc Types Utoc User Table Of ContentsAdditional Information Atrac Adaptive TRansform Acoustic Coding Sound Skip Guard Memory MD limitations Troubleshooting Possible Cause Signification Solution MD Messages Specifications JVC 0399KSMMDWJEM