JVC DR-MH30SUJ, DR-MH20SUJ manual Scan Mode Set, Press Progressive Scan for 3 or more seconds

Filename [DR-MH30UJ_10Subsidiary.fm]
DR-MH30UJ_00.book Page 69 Monday, July 12, 2004 3:17 PM	Masterpage:Right+

SUBSIDIARY SETTINGS EN 69

DISPLAY SET

8SUPERIMPOSE — OFF / AUTO

When this function is set to “AUTO”, various operational indicators appear on the TV screen. Messages appear in the selected language. ( pg. 21)

OFF: To turn off superimposed indications.

AUTO: To superimpose operational indications for approximately five seconds just after the corresponding operation.

NOTES:

●Even when “SUPERIMPOSE” is set to “OFF”, you can display the various operational indicators by pressing ON SCREEN. To clear the operational indicators, press ON SCREEN again.

●When you use this unit as the source player for editing, be sure to set “SUPERIMPOSE” to “OFF” before starting. ( pg. 62)

●When you select “AUTO”, during playback, the operation mode indicators may be disturbed depending on the type of disc being used.

8BLUE BACK — OFF / ON

When this function is set to “ON”, the TV screen becomes all blue when receiving a channel not in use.

NOTE:

When you want to receive an unstable channel with poor signals, set this function to “OFF”.

8DIMMER — BRIGHT / DIMMED1 / DIMMED2 / OFF

You can change the brightness of the front display panel.

BRIGHT: Normally select this.

DIMMED1/DIMMED2: To change the brightness level. (Blue lamp on the front display panel becomes dimmer.)

OFF: To dim the front display panel. (Blue lamp on the front display panel is turned off.)

8POWER SAVE — OFF / ON

When this function is set to “ON”, you can reduce the power consumption while the unit is turned off.

NOTES:

●During Power Save mode —

—the front display panel will be turned off.

●Power Save does not work when —

—the unit is in the Timer mode.

—the unit’s power is turned off after timer-recording or Instant Timer Recording.

—the Automatic Satellite Program Recording mode is engaged.

( pg. 50)

●It takes some time for the unit to complete initialisation after you turn on the unit power, with “WAKE UP” blinking on the front display panel.

8ON SCREEN LANGUAGE

This unit offers you the choice to view on-screen messages in 3 different languages.

For details, refer to “On-screen Language Set” ( pg. 21).

Scan Mode Set

If you connect the unit and TV with Component Video Connection ( pg. 19), you can select the scan mode from two modes: Interlaced scan mode which is used in the conventional TV system, and Progressive scan mode which enables reproduction of higher- quality images.

8Interlaced scan

In the conventional video system, a picture is shown on the display monitor in two halves. The Interlaced scan system places lines of the second half of the picture in-between lines of the first half of the picture.

8Progressive scan

Progressive scan displays all the horizontal lines of a picture at one time, as a single frame. This system can convert the interlaced video from DVD into progressive format for connection to a progressive display. It dramatically increases the vertical resolution.

ATTENTION:

Your TV needs to be compatible with Progressive.

●Turn on the unit.

●Turn on the TV and select the AV mode.

●Slide the TV/CABLE/DBS/DVD switch to DVD.

CABLE/DBS

TVDVD

PROGRESSIVE SCAN

1 Press PROGRESSIVE SCAN for 3 or more seconds.

●Video output indicator () lights on the front display panel if Progressive scan mode has been established. ( pg. 14)

●Each press of PROGRESSIVE SCAN for 3 or more seconds switches the scan mode.

NOTES:

●Interlaced scan mode is the setting at your purchase.

●Interlaced scan mode might be suitable depending on video material.

●Scan mode cannot be set while menu screen is displayed.

●When the Progressive scan mode is engaged, no video signal is output from S-VIDEO OUTPUT connectors and VIDEO/AUDIO OUTPUT connectors.

Page 69

Monday, 12 July 2004 14:10