Filename [MV5SEK_13Subsidiary.fm] |
|
MV5SEK_00.book Page 91 Wednesday, August 31, 2005 7:58 PM | Masterpage:Right0 |
|
TROUBLESHOOTING EN 91
Before requesting service for a problem, use this chart and see if |
| Playback (DVD Deck) | |
you can solve the trouble yourself. Small problems are often easily |
|
| |
solved, and this can save you the trouble of sending your unit off |
|
| |
| The DVD deck cannot be operated. | ||
for repair. |
| ||
| ● The DVD deck is not selected. | ||
Initialising (DVD Deck Only) |
| ||
| ]Press VHS/DVD on the unit repeatedly or DVD on the remote | ||
|
| control so that the DVD lamp lights up on the unit. | |
Malfunction occurs on the unit. |
|
| |
| Images do not appear on the TV screen. | ||
]Press 1 to turn off the unit, press and hold 1, then press 8 |
| ||
| ● The TV receiver’s channel selector is not set to the AV mode. | ||
for two seconds or more. |
| ||
| ]Set the TV to its AV mode. | ||
General |
| ||
| ● When interlace scanned programme is played back, progressive | ||
|
| ||
|
| scan mode is selected. | |
|
| ]Press and hold PROGRESSIVE SCAN until disappears from | |
No power is supplied to the unit. | |||
| the front display panel. ( pg. 80) | ||
|
|
●The AC power plug is disconnected from the AC outlet.
]Connect the AC power plug to the AC outlet securely. ( pg. 15) |
| Playback does not start or stop immediately after playback is | ||
|
| started by pressing | . | |
The disc tray cannot be opened. |
| On the front display | panel, “NO DISC” appears. | |
]Open the disc tray by following the steps below. |
| ● The disc is loaded upside down. | ||
1. Press 8 and 1 on the unit simultaneously. |
| ]Place the disc on the disc tray with the playback surface facing | ||
2. Press and hold x (OPEN/CLOSE) on the unit for |
| down. ( pg. 9) | ||
approximately 30 seconds until the tray is opened. |
| ● A disc not being compatible with the unit is loaded. | ||
3. Remove the disc, then press x (OPEN/CLOSE). The unit |
| ]Load a playable disc on the unit. ( pg. 6) | ||
shuts off. |
| ● A dirty disc is loaded. | ||
|
| ]Clean the disc. ( pg. 9) | ||
The remote control does not work properly. | ||||
| ● Defective disc is loaded. | |||
|
| |||
]Remove the batteries, wait for 5 minutes or more, then load the |
| ]Replace the warped or scratched disc with a normal one. | ||
batteries again. |
|
|
| |
| Images are blurred or distorted when you start | |||
● The setting of the remote control code is inappropriate. |
| |||
| Search. | |||
]Set the same remote control code (1, 2, 3, or 4) on both the unit |
| |||
| ]Images are blurred or distorted at the point where the playback | |||
and the remote control. ( pg. 74) |
| |||
● The batteries are discharged. |
| speed changes and this is not a malfunction of the unit. | ||
]Replace the dead batteries with new ones. |
|
|
| |
| Playback does not start. | |||
|
| |||
|
|
|
| |
Dubbing from the external equipment is not possible. |
| ]Playback does not start for approximately 30 seconds after | ||
● The source (another video recorder, camcorder) has not been |
| recording is stopped and this is not a malfunction of the unit. | ||
properly connected. |
|
|
| |
]Confirm that the source is properly connected. |
|
|
|
●All necessary power switches have not been turned on. ]Confirm that all units’ power switches are turned on.
●The setting of the input channel position is inappropriate. ]Select the input channel position
corresponds to the input terminal connected to the external equipment. ( pg. 43)
The
]Set “SUPERIMPOSE” to “OFF”. ( pg. 79)
The unit does not operate.
●There are cases when the operation is prohibited on the disc.
●Lightning or static electricity may cause malfunction of the unit. ]Press 1 to turn the power off, then press the button again to
turn the power on.
The remote control of a JVC TV will not operate the unit.
●The setting of the remote control code is inappropriate. ]To operate the unit using a JVC TV remote control, set the
remote control code of the unit to “1” (Default: “3”). ( pg. 74)
Page 91Wednesday, 31 August 2005 19:58 |