Connections
Rear panel
Security slotAttach a security wire to this slot.
Note for connections• Before making any connections, turn off all the equipment.
• Use a cord whose plugs correctly match the terminals on this monitor and the equipment.
• Plugs should be firmly inserted; poor connections could cause noise.
• When unplugging a cord, be sure to grasp its plug and pull it out.
• DO NOT connect the power cord until all connections are complete.
• Refer also to the user manual of each piece of equipment.
AC power input connector. Connect the provided AC power cord to an AC outlet.
●Attach the provided power cord holder to prevent accidental disconnection of the AC power cord. (☞ below)
●Please review "Safety Precautions (a grounding type plug)" on page 4 carefully.
Caution: Do not connect the power cord until all other connections are completed.
2AC POWER switch Turns AC power on or off.
●You need to press
button (☞ u on page 10) to use the monitor after turning on the AC POWER switch.
Terminal for controlling the monitor by an external control (☞ “External Control” on page 22).
4VIDEO terminals (BNC)Input (IN) and output (OUT) terminals for the composite signals.
5COMPO. (Y,Input (IN) and output (OUT) terminals for the analog component (color difference) signal.
6AUDIO (IN) terminals (pin jack)Input terminals for the analog audio signals.
●Use this terminal for the analog audio connection of the SDI. When a superimposed signal (EMBEDDED AUDIO signal on an SDI signal) is input, analog audio signals cannot be input.
7AUDIO MONITOR OUT (OUT 1, OUT 2) terminals (pin jack) Output terminals for the analog audio signal.
●The terminals emit the audio signals through the AUDIO (IN) terminal or EMBEDDED AUDIO signals through the E. AUDIO 3G SDI/HD SDI/SD SDI (IN 1 or IN 2) input terminal.
●The signal is output from this terminal only when the monitor is on or in “P.SAVE” (power save) mode (☞ “NO SYNC ACTION” on page 17).
●The EMBEDDED AUDIO signal...
–is decoded into an analog signal, then emitted.
–is emitted only when “SDI 1” or “SDI 2” is selected, and when EMBEDDED AUDIO signals come in to the E. AUDIO 3G SDI/ HD SDI/SD SDI (IN 1 or IN 2) terminal.
8E. AUDIO 3G SDI/HD SDI/SD SDI (IN 1, IN 2) terminals (BNC) Input terminals for the 3G SDI/HD SDI/SD SDI signals.
●The terminals accept also EMBEDDED AUDIO signals including up to 16 audio channels with a sampling frequency of 48 kHz.
●Use SDI IN 1 and SDI IN 2 terminal when selecting DUAL LINK SDI for the input.
9E.AUDIO 3G SDI/HD SDI/SD SDI (SWITCHED OUT) terminal (BNC)Output terminal for the 3G SDI/HD SDI/SD SDI signals.
●The SDI signals of the current input (SDI 1 or SDI 2) are re- clocked, then emitted.
●When an input other than SDI 1 and SDI 2 is selected, the SDI signal of the input selected last time is emitted from this terminal.
●The signals are emitted from this terminal only when the monitor is on or in “P.SAVE” (power save) mode.
●No signals are emitted when DUAL LINK SDI is selected for the input.
pInput terminal for the
●When the picture is not displayed correctly, change the setting of “DVI INPUT SEL.” (☞ page 20)
The provided power cord holder prevents accidental disconnection of the AC power cord from the AC IN terminal. The holder consists of two parts: the cord case and the case cover.
1 cord case | AC IN terminal | 2 | case cover | 3 |
|
To take off the case cover
●Do not use any screws other than those supplied.
●Push the case cover into the cord case and check that the power plug is connected firmly.
8