JVC GR-DV3000 4, 5, 10, 6, 7, 8, 9

––:–– ~

––

0:000

––

TOTAL

ECODEM

NIOUT

MODE

CANCEL

R.A.EDIT

ON/OFF

PLAY

FADE/WIPE

EFFECT

EDIT IN/OUT

SELECT SCENES

4Point the remote control at the camcorder’s

remote sensor. Press PLAY (

) and then press

R.A.EDIT ON/OFF on the remote control.

The Random Assemble Editing Menu appears.

5If using a Fade/Wipe at the beginning of the

scene, press FADE/WIPE on the remote control.

•Cycle through the effects by pressing repeatedly,

and stop when the one you want is displayed.

•You cannot use a Picture Wipe/Dissolve at the

beginning of Program 1.

6At the beginning of the scene, press EDIT IN/

OUT on the remote control. The Edit-In position

appears in the Random Assemble Editing Menu.

7At the end of the scene, press EDIT IN/OUT. The

Edit-Out position appears in the Random Assemble

Editing Menu.

8If using a Fade/Wipe at the end of the scene,

press FADE/WIPE.

•Cycle through the effects by pressing repeatedly,

and stop when the one you want is displayed.

•If you select a Fade/Wipe effect for an Edit-Out

point, the effect is automatically applied to the

following Edit-In point.

•You cannot use a Picture Wipe/Dissolve at the end

of the last scene.

•When you use Fade/Wipe effects, that time is

included in the total time (this does not apply to

Picture Wipe/Dissolve).

9If using Playback Special Effects, press EFFECT

( pg. 65).

Repeat steps 6 through 9 to register additional

scenes.

•To change previously registered points, press

CANCEL on the remote control. The registered

points disappear, one at a time, from the most

recently registered point.

•If you are not using Fade/Wipe or Program AE with

special effects, repeat steps 6 and 7 only.

NOTES:

●When choosing a scene, set Edit-In and Edit-Out points so

that there is a relatively large difference between them.

●If the search time for an in-point exceeds 5 minutes, the

recording deck’s Record-Standby mode will be canceled

and editing will not take place.

●If there are blank portions before or after the Edit-In and

Edit-Out points, a blue screen may be included in the edited

version.

●Since time codes register time only as accurately as

seconds, the time code total time may not match the total

program time exactly.

●Turning off the camcorder’s power erases all registered Edit-

In and Edit-Out points.

●

If you select Sepia or Monotone mode from Program AE with

special effects, you cannot use the Dissolve or Black & White

Fader. In this case the Dissolve or Black & White indicator

begins blinking. Once the next Edit-In point is registered, the

effect is turned off. To combine these effects, use Sepia or

Monotone during recording, then use the Dissolve or Black &

White Fader during Random Assemble Editing.

●It is not possible to use Fade/Wipe effects and Program AE

with special effects during Random Assemble Editing using

a DV cable.

Random

Assemble

Editing

Program

Remote sensor

USING THE REMOTE CONTROL UNIT

(cont.)

Fader And Wipe Menu (available only for

Random Assemble Editing)

You can also use the fade/wipe effects on page 37.

DISSOLVE

The new scene gradually appears as the old one

gradually disappears.

WIPE — CORNER

The new scene wipes in over the previous one from

the upper right corner to the lower left corner.

WIPE — WINDOW

The next scene gradually wipes in from the center of

the screen toward the corners, covering the previous

scene.

WIPE — SLIDE

The next scene gradually wipes in over the previous

one from right to left.

WIPE — DOOR

The previous scene wipes out from the center to the

right and left, like a door being pushed open to reveal

the next scene.

WIPE — SCROLL

The new scene wipes in over the last one from the

bottom of the screen to the top.

WIPE — SHUTTER

The new scene wipes in over the previous one from

the center toward the top and bottom of the screen.