JVC HR-S9400EH specifications Enter Showview Number, Confirm Channel Position Number, Close Menu

		ENTER SHOWVIEW
		NUMBER
		Press OK, and a cursor			GUIDE PROG SET
		appears above “GUIDE
4 PROG”. Then, using the				1 2 3 4 5
		NUMBER keys, input the		GUIDE PROG		TV PROG
		SHOWVIEW number (found	1			1
		in most TV listings) of a
		program scheduled to be
		broadcast on each station
			[0-9] =
		on the list from step 1,	[MENU] : EXIT
	starting at the top. If you		When entering a SHOWVIEW
	enter the wrong number,
			number for ZDF
	press CANCEL to backspace
	and input the correct number.
		CONFIRM CHANNEL
		POSITION NUMBER
4		Press OK and the display			GUIDE PROG SET
		under “TV PROG” begins
5 blinking.
		If the blinking number		GUIDE PROG		TV PROG
		under “TV PROG” agrees
					2	2
		with the channel
		position . . .
		. . . press OK.	[5°] =
		If the numbers do not	[MENU] : EXIT
		agree . . .
		. . . input the channel position using PUSH JOG%Þ or
	the NUMBER keys, then press OK.

●If you input the SHOWVIEW number of a program that has already aired, “ERROR” appears on screen for a few seconds. Input the correct SHOWVIEW number.

●Repeat steps 4 and 5 as necessary.

CLOSE MENU

6 Press MENU and selection is complete.

If you already know the Guide Program number for a station . . .

1– After step 3, press PUSH JOG %.

●The GUIDE PROG number begins blinking.

2– Enter the Guide Program number using the NUMBER keys or PUSH JOG%Þ, then press PUSH JOG %.

●The TV PROG number begins blinking.

3– Enter the channel position using the NUMBER keys or PUSH JOG%Þ, then press PUSH JOG% .

●Repeat 2 and 3 as necessary. 4– Press MENU.

EN13

When Using A Satellite

Tuner

Satellite Antenna		Aerial or Cable
Ex. 1	Ex. 2
Satellite	Satellite
	Tuner and
Tuner
	Decoder
AV2 IN/
DECODER

Rear view

TV Receiver

For Customers in

Australia and New Zealand:

When connecting

the AV cable, use

the input and/or

output cable

adapter.

Preparation

1– Connect the satellite tuner to the AV2 IN/DECODER connector on the rear of your recorder.

2– Set "AV2 SELECT" to "AV2" (☞ pg. 35).

To Record Satellite Broadcasts . . .

1– Select the appropriate channel on the satellite tuner. 2– Set your recorder's input mode to "AUX2". (☞ pg. 35) 3– Start recording (☞ pg. 23, steps 3 – 6).

To Record Satellite Broadcasts Using SHOWVIEW Timer Recording . . .

1– Set your recorder's input mode to "AUX2". (☞ pg. 35) 2– Perform Guide Program Number setting.

●In step 5 in the left column, press NUMBER key "0" to set "TV PROG" to "AUX2".

3– Perform SHOWVIEW Timer Recording (☞ pg. 28).

To Record Satellite Broadcasts Using Regular Timer Recording . . .

1– In step 6 on page 31, press TV PROG +/– to set the channel position to "AUX2".

NOTES:

●When timer-recording a satellite programme, first set the satellite tuner to the appropriate channel before the selected programme begins and then set the satellite tuner's timer. If your satellite tuner does not have a timer, leave it switched on.

●If your recorder's front panel VIDEO and/or AUDIO connec- tors are being used, they take priority and "AUX2" cannot be selected. Make sure no cables are connected to the front panel connectors when performing this procedure.