JVC HR-XV32E manual 66 EN, Picture Settings, Audio Settings, MasterpageLeft+

Filename [XV3EX_10Subsidiary.fm]

XV3EX_01.book Page 66 Friday, August 22, 2003 12:21 PM

66 EN

Masterpage:Left+

SUBSIDIARY SETTINGS (cont.)

* The default setting is bold in the table below.

Picture Settings

8MONITOR TYPE —

16:9 NORMAL / 16:9 AUTO / 4:3 LB / 4:3 PS

You can select the monitor type depending on the TV used when you play back DVD VIDEO discs recorded for wide-screen TVs. For more details, refer to “Monitor Set (DVD deck)” ( pg. 14).

8PICTURE SOURCE —

VIDEO (NORMAL) / VIDEO (ACTIVE) / FILM / AUTO

You can obtain optimal picture quality by selecting whether the content on the disc is processed by field (video source) or by frame (film source).

Normally set to “AUTO”.

VIDEO (NORMAL): Suitable for playing back a video source disc with relatively a few movements.

VIDEO (ACTIVE): Suitable for playing back a video source disc with relatively a lot of movements.

FILM: Suitable for playing back a film or progressive source disc.

AUTO: Used to play back a disc containing both video and film source materials. This unit recognizes the picture type (film or video source) of the current disc according to the disc information.

●If the playback picture is unclear or noisy, or the oblique lines of the picture are rough, try to change to other modes.

8SCREEN SAVER — ON / OFF

The TV screen may be burned out if a static picture is displayed for a long time. When this function is set to “ON”, the unit automatically activates the screen saver function if a static picture, such as an on-screen display or menu is displayed for over 5 minutes.

8ANALOG DOWN MIX — DOLBY SURROUND / STEREO

Set to the appropriate mode according to your audio system when you play back a DVD VIDEO disc recorded with surround multichannel audio. This setting affects only the analogue audio output signal from the AUDIO OUT connectors when playing back a DVD VIDEO disc recorded with surround multichannel audio.

DOLBY SURROUND: Select this when you enjoy multichannel surround audio by connecting the unit’s analogue AUDIO OUTPUT connectors (DVD) to a surround decoder or an internal amplifier.

STEREO: Select this when you enjoy conventional 2-channel stereo audio by connecting the unit’s analogue AUDIO OUTPUT connectors (DVD) to a stereo amplifier/receiver or TV, or when you dub audio of a DVD VIDEO disc recorded with surround audio to your MD, cassette, etc.

NOTE:

The “ANALOG DOWN MIX” function does not work when the 3D Phonic function is activated. ( pg. 33)

8D. RANGE CONTROL —

WIDE RANGE / NORMAL / TV MODE

The dynamic range (the difference between the loudest sound and the quietest one) can be compressed during playback of a programme encoded in Dolby Digital format.

This function takes effect when a DVD VIDEO disc recorded in Dolby Digital format is played back at low or middle volume. WIDE RANGE: Select this to inactivate this function when you

enjoy wide dynamic range programme.

NORMAL: Normally select this setting to activate this function.

TV MODE: Select this when you hear the sound through the TV's speaker(s).

NOTE:

This function is not available for Audio CDs and MP3 discs.

8MP3/JPEG — MP3 / JPEG

You can select files to play back, when both MP3 files and JPEG files are recorded on a disc.

MP3: Select this to play back MP3 files.

JPEG: Select this to play back JPEG files.

NOTE:

You cannot access the DVD Set Up screen and “X” appears on the TV screen if a disc is already placed.

NOTES:

●This function works only when playing back a disc recorded with Dolby Digital format. The setting is not effective for other discs.

●This function does not work when the 3D Phonic function is activated. ( pg. 33)

8OUTPUT LEVEL — STANDARD / LOW

You can lower the output level of analog audio to accommodate the unit to the connected A/V equipment.

STANDARD: Normally select this.

LOW: The output level of analog audio is lowered.

Audio Settings

8DIGITAL AUDIO OUTPUT —

PCM ONLY / DOLBY DIGITAL/PCM / STREAM/PCM

Set to the appropriate mode according to the type of the device connected to DIGITAL AUDIO OUT connector on the rear of unit.

It is not necessary to set this mode when you connect no device to the DIGITAL AUDIO OUT connector.

PCM ONLY: Select this when you connect the unit’s DIGITAL AUDIO OUT connector to the linear PCM digital input connector of another audio device.

DOLBY DIGITAL/PCM: Select this when you connect the unit’s DIGITAL AUDIO OUT connector to the digital input connector of a Dolby Digital decoder or an amplifier with a built-in Dolby Digital decoder.

STREAM/PCM: Select this when you connect the unit’s DIGITAL AUDIO OUT connector to the digital input connector of an amplifier with a built-in DTS, Dolby Digital, or MPEG multichannel decoder.

Page 66

August 22, 2003 12:20 pm