JVC RX-DP20VBK manual Setting the Surround Channel Output Speakers-SURR CH OUT

6 Setting the Surround Channel Output

Speakers—SURR CH OUT

On this submenu screen, you can preset which surround speakers to use for 5.1 channel reproduction.

Note:

This submenu is not available in the following cases:

–When “SURR BACK OUT” is set to “1SPK” on the SPEAKER SETTING submenu,

–“SURR BACK SP” is set to “NONE” on the SPEAKER SETTING submenu,

–“SPEAKER 2” is set to “BI-AMP OUT” on the ZONE 2/SPEAKER 2 submenu, or

–When the Zone 2 speakers are activated.

7SURROUND SP

Select the surround channel output speakers from the following:

SURR	: Select to use the left and right surround
	speakers—recommended setting for Dolby
	Pro Logic and Pro Logic II.
SBACK	: Select to use only the surround back speakers.
SURR+SB	: Select to use both the surround speakers and
	surround back speakers.

7DUAL MONO

Select the playback sounds (channel).

MAIN	: Select to play back the main channel (Ch1).*1
	Signal indicator “L” lights up while playing back
	this channel.
SUB	: Select to play back the sub-channel (Ch2).*1
	Signal indicator “R” lights up while playing back
	this channel.
ALL	: Select to play back both the main and sub-channels
	(Ch1/Ch2).*1
	Signal indicators “L” and “R” light up while playing
	back these channels.

Notes:

•The Dual Mono format is not identical with bilingual broadcasting or the MTS (Multi-channel TV Sound) format used for TV programs. So this setting does not take effect while

watching bilingual or MTS programs.

*1 Dual Mono signals can be heard from the following speakers— L (left front speaker), R (right front speaker), and C (center speaker)—with respect to the current Surround setting.

	Without Surround			With Surround Activated
Dual Mono				Center speaker setting
Setting			LARGE/SMALL			NONE
	L	R	L	C	R	L	R
MAIN	Ch 1	Ch 1	—	Ch1	—	Ch 1	Ch 1
SUB	Ch 2	Ch 2	—	Ch2	—	Ch 2	Ch 2
ALL	Ch 1	Ch 2	—	Ch1+Ch2	—	Ch1+Ch2	Ch1+Ch2

7 Setting the Audio Delay Level—AUDIO DELAY

Synchronization between audio and video reproduction can be possibly disturbed because video signal decoding is time- consuming compared to the audio signal decoding.

On this submenu screen, you can correct synchronization between video and audio signals by delaying the audio signal timing.

7AUDIO DELAY

Adjust the delay time within the range of 0 ms (initial setting: no effect) to 200 ms (maximum) in 20 ms intervals.

8 Selecting the Dual Mono Sound—DUAL MONO

On this submenu screen, you can select the playback sound (channel) you want while playing digital software recorded (or broadcast) in the Dual Mono mode, which includes two monaural channels separately.

9 Setting the Digital Input/Output Terminals

—DIGITAL IN/OUT

When you use the digital input and output terminals on the rear, you have to register what components you have connected to these digital terminals.

7COAX IN 1/2/3, OPT IN 4/5/6

Select the name of the component connected to each digital terminal so that it will correspond to the source selecting button on the unit and on the remote control.

•Each time you press # or @ (RIGHT or LEFT), the component name changes as follows:

DVD “ CD “ TV (or DBS*2) “ CDR “ MD “ VCR1 “ (back to the beginning)

Notes:

•If you have selected the same source for different terminals, only the last performed terminal setting will be valid. (The other

terminal settings will be automatically set to “OFF.”)

*2 If you have changed the source name from “TV” to “DBS,” “DBS” appears (see page 27).

Continued on the next page

42