JVC RX-DP20VBK manual Operating Video Components, VCR VCR connected to the VCR 1 jacks, DVD player

TV

CATV/

DBS

Operating Video Components

IMPORTANT:

To operate JVC’s video components using this remote control:

•You need to connect JVC’s video components through the AV COMPU LINK jacks (see page 68) in addition to the connections using cables with RCA pin plugs (see pages 13 to 15).

•Some JVC VCRs can accept two types of control signals—remote codes “A” and “B.” Before using this remote control, make sure that the remote control code of the VCR connected to the VCR 1 IN jacks is set to code “A.”

–When another JVC VCR is connected to the VCR 2 IN and VIDEO jacks, set its remote control code to code “B.” (This remote control cannot emit the control signals of code “B.”)

•To operate the video component(s) using the remote control:

–Aim the remote control directly at the remote sensor on each component, not on the receiver.

•To operate the video component(s) using the RF signals emitted from this remote control, the IR signal transmitter and the RF rod antenna must be connected to this receiver.

–Place the IR signal transmitter so that it is aimed at the remote sensor(s) on the target video component(s).

–The RF signal-reachable distance may differ depending on the operating conditions and circumstances.

–The IR signal transmitter can send signals from a distance of 3 m (10 feet).

When using the remote control:

–Set the ZONE 1/ZONE 2 (LEARN/TRANSMIT) selector to “ZONE 1” or “ZONE 2” correctly.

LEARN	TRANSMIT	LEARN	TRANSMIT
ZONE 1	ZONE 2	ZONE 1	ZONE 2

– Set the TV operation mode selector to “TV” or “CATV/DBS” properly.

To operate TV, set it to “TV.”

–Check the indication shown on the remote’s display when you press a button—this indicates the remote

control operation mode together with multi-room operation mode (either ZONE 1 or ZONE 2) for a while.

–The CONTROL button can change the remote control operation mode without changing the source.

Each time you press the button, the remote control operation mode changes in the sequence—VCR1 = TAPE = CDR = CD DISC = (back to the beginning).

LEARN	TRANSMIT		LEARN	TRANSMIT
	STANDBY	ON		STANDBY	ON
ZONE 1	ZONE 2		ZONE 1	ZONE 2
ZONE 1	ZONE 2 TV/CATV/DBS	VCR 1
			ZONE 1	ZONE 2 TV/CATV/DBS	VCR 1
ON/OFF	ON/OFF		ON/OFF	ON/OFF
	STANDBY/ON	STANDBY/ON		STANDBY/ON	STANDBY/ON

ZONE 1 ZONE 2

Ex. When you press VCR1	Ex. When you press VCR1
with ZONE 1/ZONE 2	with ZONE 1/ZONE 2
(LEARN/TRANSMIT)	(LEARN/TRANSMIT)
selector set to “ZONE 1.”	selector set to “ZONE 2.”

VCR (VCR connected to the VCR 1 jacks)

You can always perform the following operations:

VCR 1 (STANDBY/ON): Turns on or off the VCR.

After pressing VCR 1 or selecting “VCR1” by pressing CONTROL repeatedly, you can perform the following operations on the VCR:

1 – 9, 0	: Selects the TV channels on the VCR.
PLAY	: Starts playing.
REW	: Rewinds a tape.

FF: Fast-winds a tape.

STOP	: Stops operations.
PAUSE	: Pauses playing. To release, press PLAY.
¶ REC	: Press this button together with the PLAY button
	to start recording (only for Zone 1 operations).
	Press this button together with the PAUSE button

to enter recording pause (only for Zone 1 operations).

CHANNEL +/– : Changes the TV channels on the VCR.

DVD player

After pressing DVD (or DVD MULTI: only for Zone 1 operations), you can perform the following operations on the DVD player:

1 – 10, 0, +10 : Selects the DVD titles or the chapters.

PLAY : Starts playing.

4: Returns to the beginning of the current (or

previous) chapter.

¢: Skips to the beginning of the next chapter.

STOP	: Stops playing.
PAUSE	: Stops playing temporarily. To release, press
	PLAY.

After pressing DVD MENU, these buttons can be used for the DVD menu operations.

SET

DVD

MENU

Note:

Refer also to the manual supplied for your DVD player (and the instruction supplied for the discs).

TV

You can always perform the following operations (with the TV operation mode selector set to “TV”):

TV/CATV/DBS (STANDBY/ON)

:Turns on or off the TV.

TV VOL +/– : Adjusts the volume.

TV/VIDEO : Sets the input mode (either TV or VIDEO).

After pressing TV/DBS (with the TV operation mode selector set to “TV”), you can perform the following operations on a TV:

CHANNEL +/– : Changes the channels.

1 – 9, 0, 100+ : Selects the channels.

RETURN : Alternates between the previously selected channel and the current channel.

73