JVC SR-9168U appendix Alarm/sensor, RS-232C, Parameter Setting

5 SETTING OF THE FUNCTION MENU SWITCHES

5-2 Contents of the Function Menu Switches

[ ]: Factory setting

Screens	Items	Set values			Function
VTR mode 2	COUNT END	[OFF]	Sets the timing to process tape end at a specified counter value rather than at
setting		500	the actual tape end. This menu switch setting is effective in the 48H to 240H
		1000	Record modes. For the 6H to L30H modes, set with <REC REMAIN>. The
		:	following operations are executed at the timing set with this menu switch.
		:	• The tape end signal is output from the rear panel's [TAPE END] terminal.
		9500	• The series recording signal is output from the rear panel's [CLOCK/SERIES
			OUT] terminal (with the TERMINAL SEL 1> function menu switch set to
			"SERIES").
			• The tape end buzzer sounds (with the <TAPE END BUZZER> function menu
			switch set to "ON").
			• "End" is shown on the counter display.
			OFF: Executes tape end processing at the actual tape end.
			5000 - 9500: Executes tape end processing at the set tape counter value.
			To determine the set tape counter value according to the tape length, refer to
			the table on page 53.
Alarm/sensor	ALARM REC	[OFF]	Turns the alarm recording function on or off.
recording mode		ON	Alarm recording is enabled only in the Timelapse Record mode.
setting			An index code (VISS signal) is also recorded at the start point of alarm
			recording as an alarm cue signal.
			OFF : Alarm recording is disabled.
			ON	: This unit enters the specified Record mode, when an alarm signal is
				input to the rear panel's [ALARM IN] terminal during timelapse recording.
	SENSOR REC	[OFF]	Turns the sensor recording function on or off. Sensor recording is enabled in
		ON	the Stop mode. An index code (VISS signal) is also recorded at the start point of
			sensor recording.
			OFF : Sensor recording is disabled.
			ON	: When an alarm signal is input to the rear panel's [ALARM IN] terminal in
				the Stop mode. This unit automatically starts recording in the specified
				Record mode.
	REC MODE	[6H]	Selects the recording mode for alarm recording or sensor recording.
		18H	6H : Recording is executed in the 6H(EP) mode.
		30H	18H : Recording is executed in the 18H mode.This value is not selected when
			the <DURATION> function menu switch is set to "5 sec".
			30H	: Recording is executed in the 30H mode. This value is not selected when
				the <DURATION> function menu switch is set to "5 sec" or "15 sec ".
	DURATION	5	Selects the recording duration for alarm recording or sensor recording.
		15	5 ..... 180		: Alarm or sensor recording is performed for the time specified (5 sec.
		30			to 180 sec.).
		60			• 5 sec is not selected when the <RECMODE> function menu
		120			switch is set to "18H".
		[180]			• 5 or 15 sec is not selected when the <REC MODE> function menu
		TAPE END			switch is set to "30H".
		MANUAL	TAPE END: Alarm or sensor recording continues until the tape ends.
			MANUAL		: Alarm or sensor recording continues for as long as alarm signals
					are input.
					Set to this position when specifying the alarm recording time with a
					switcher.
	BUZZER	[OFF]	Selects whether or not the alarm buzzer sounds during alarm or sensor
		ON	recording.
			OFF : The buzzer does not sound.
			ON	: The buzzer sounds.
	TAPE END	[STOP]	Set the operation mode at tape end during recording in the case when alarm or
	MODE	REW	sensor recording is executed even once.
		REPEAT	STOP		: Stops at tape end.
		EJECT	REW		: Rewinds the tape automatically and stops.
			REPEAT		: Rewinds the tape automatically to the beginning and restarts
					recording.
			EJECT		: The tape is ejected.
RS-232C
	This screen is displayed on the on-screen setting screen only when the (optional) RS-232C board SA-K97U is installed.
parameter
setting	BAUD RATE	1200	Select the RS-232C data transfer speed from 1200 bps, 2400 bps, 4800 bps or
		2400	9600 bps.
		4800
		[9600]

20