JVC XL-R5000BK manual CDR Playback Operations, Using the Remote Control to Control Playback

RECindicator lights

Concerning the CD numbers and play status display

The display shows for each CD tray whether or not a CD has been inserted as well as the play status of the CD.

While a CD is playing, this lights in sequence, and blinks in the pause mode. It goes off when “NO DISC” is displayed to indicate that a disc has not been loaded.

The CD on the CD tray for which this has lighted is selected.

CDR Playback Operations

The CDR section can be used to play back CDs, CD-R, and CD- RW.

2	1
XL - R5000 CD/CDR MULTIPLE COMPACT DISC RECORDER	REC LEVEL
	MIN	MAX
	MIX BALANCE	PHONES LEVEL
MULTI JOG

STANDBY
–	+
POWER

7 8 3

1 Press the EJECT 0button to open the CDR disc tray.

2 Load a disc in position and close the tray.

•When a CD-R or CD-RW is loaded in the CDR for the first time, OPC (Optimize Power Control) is performed. This proce- dure requires anywhere from 10 seconds up to a minute to per- form. Once OPC has been performed, the unit stores the information for that disc in memory (occasionally some older data will be erased and OPC may need to be performed again in these cases).

•When a CD-R or CD-RW is loaded in the CDR, the unit deter- mines the format of the disc, whether it is finalized or not, and then determines whether OPC (Optimize Power Control) has been performed for the disc or not. At this time, OPC is also performed if necessary. The length of time required for this unit

to perform the necessary operations depends on the type and status of the disc.

• When “UPDATE OPC” is displayed, the and the 3and disc format indicator flashes.

3 Press the CDR CONTROL 3button to select the

CDR function and start playback at track 1.

•Playback is automatically stopped at the end of the last track on the disc.

•Unfinalized CD-R and CD-RW may be played back using the CDR. Unfinalized discs cannot be played back using the 3-CD changer.

To stop CDR playback

•Pressing the CDR CONTROL 7 (stop) button at any point dur- ing playback stops the playback and the total track number and play time appear in the display.

•When an unfinalized CD-R or CD-RW is loaded in the CDR and the EJECT 0 button is pressed to open the CDR disc tray, “FINALIZE?” appears in the display window. If you do not wish to finalize the disc at this time, press the EJECT 0 button again. For more information on finalization, see page 29.

To stop CDR playback temporarily

•Pressing the CDR CONTROL 8(pause) button at any time dur- ing playback pauses the playback. Press the 3 button to resume playback.

• When playback is paused, the 8indicator lights in the display.

Note

Before finalization of the disc is performed, when you playback of the disc is started from the stop mode or at a track that is skipped forward or reverse to etc., the very beginning of the track may cut.

Using the Remote Control to Control Playback

The buttons on the remote control can be used to control playback of both the 3-CD changer and CDR. When using the remote con- trol, be sure to point the remote control correctly at the remote con- trol sensor on the main unit when pressing the buttons.

CD REC	SYNCHRO	DISPLAY POWER
CD EDIT	FINALIZE	MENU

			CD 1
1	2	3
			CD 2	CD 1, CD 2, CD 3
4	5	6

			CD 3
7	8	9
		CONTROL
10	+10	CD	CDR	1
PLAY MODE	REPEAT	SET	CANCEL

PITCH +

PITCH 0	2
	REC

PITCH –

SHIFT REC MUTING

REMOTE CONTROL

RM-SXLR5000J

1 Press the CD or CDR button to select the

function.

CD button: To control discs in the 3-CD changer

CDR button: To control the disc in the CDR

12