Fixed Station Operation | Kenwood TM-D700 E specification

■Fixed Station Operation

1In order to use this transceiver for fixed station operation, you will need a separate 13.8 V DC power supply that must be purchased separately. The recommended current capacity of your power supply is 12 A.

1Connect the DC power cable to the regulated DC power supply and check that polarities are correct (Red: positive, Black: negative).

•DO NOT directly connect the transceiver to an AC outlet.

•Use the supplied DC power cable to connect the transceiver to a regulated power supply.

•Do not substitute a cable with smaller gauge wires.

2Connect the transceiver’s DC power connector to the connector on the DC power cable.

•Press the connectors firmly together until the locking tab clicks.

Fuse holder

Note:

◆	For your transceiver to fully exhibit its performance capabilities,
	the following optional power supply is recommended:
	PS-33 (20.5 A, 25% duty cycle).
◆	Before connecting the DC power supply to the transceiver, be
	sure to switch the transceiver and the DC power supply OFF.

Fuse holder

Red (+)

Black (–)

Regulated DC power supply

To AC outlet

◆ Do not plug the DC power supply into an AC outlet until you

make all connections.

6

Image 12

Kenwood TM-D700 E instruction manual Fixed Station Operation, PS-33 20.5 A, 25% duty cycle

Contents

TM-D700A Features Thank YOUModels Covered by this Manual When condensation occurs inside the transceiver One or more of the following statements may be applicable Contents Selecting the Number of Channels Using Visual Scan Setting Scan Limits Using Program ScanRecalling the Call Channel Reprogramming the Call Channel Locking Out a Memory Channel Changing MULTI-FUNCTION Squelch Hang Time Supplied Accessories Conventions Followed in this Manual Mobile Installation Main Unit InstallationPreparation Front Panel Installation Slide the front panel down until its locking tab clicks Fixed Station Installation Modular Plug Cable Connection DC Power Cable Connection Mobile Operation Fixed Station Operation PS-33 20.5 A, 25% duty cycle Transceiver 15 a Supplied Accessory 20 a DC Power Cable Antenna ConnectionReplacing Fuses Fuse Location Fuse Current Rating Accessory Connections External SpeakersMicrophone Your First QSO Ew wew w Getting Acquainted Front Panel 3SQL control Main UNIT- Front Main UNIT- RearGPS jack Microphone Indicators Basic Transceiver Modes Button Function Display Band a & B TX Band and Control BandTX Band Control Band MIC Keypad Direct Entry MC-53DM only Switching Power ON/OFF Adjusting VolumeSwitch on the DC power supply Operating Basics Adjusting Squelch Selecting a Frequency Selecting Output Power When you finish speaking, release Mic PTTTransmitting Menu Access Press MNU to enter Menu modeMenu SET-UP Press c/ d to select the appropriate level 1 No Press OK Menu Configuration Level Selections Default Auto PM Channel Store Channel DisplayMemory Channel Lockout Memory channel name See reference Number Store Visual Scan Automatic Power Off APO Remote ControlMic PF Key See reference Mic MR Key Mic VFO Key See reference My call sign See reference Color for call sign WhiteMessage See reference Color for message RSV report See reference Color for RSV report Commander call sign See reference Transporter call sign Sky Command modeStatus text transmit rate See reference Packet path See reference Operating Through Repeaters Offset Programming Flow Programming Offset Selecting Offset DirectionSelecting Offset Frequency Press c / d to select Radio 1-, then press Activating Tone Function Selecting a Tone FrequencyPress Tone to activate the Tone function Press F, T.SEL Automatic Repeater Offset A. and Canada versions Transmitting a 1750 Hz Tone Press REV to switch the Reverse function on or OFF Reverse FunctionAutomatic Simplex Check ASC Tone FREQ. ID Press Scan to activate the Tone Freq. ID Memory Channels Simplex & Repeater or ODD-SPLIT Memory CHANNEL?Parameter Simplex Odd-split Storing ODD-SPLIT Repeater Frequencies Press M.IN 1 sSelect the desired transmit frequency Press M.IN Select band a or B Press MR to enter Memory Recall mode Press MHz Tuning control+ Power onRecalling a Memory Channel Clearing a Memory Channel Turn the Tuning control to select the first digit Naming a Memory ChannelPress a Repeat steps 6 and 7 to enter up to 8 digits Call Channel Recalling the Call ChannelReprogramming the Call Channel Press VFO MEMORY-TO-VFO Transfer Channel Display Partial or Full RESET? ParameterBand B 440.000 MHz Programmable Memory PM Programmable Information Application Examples Situationit ti Storing in PM Channels Recalling a PM Channel PM Channel Reset Press PM+ Power onAuto PM Channel Store Scan Scan Type Scan Range Mode 1 31 ch Mode 2 61 chVisual Scan Selecting the Number of Channels Using Visual Scan Press F, Visual to start Visual ScanTo quit Visual Scan, press ESC Time-Operated mode Carrier-Operated modeSeek mode Selecting Scan Resume Method VFO Scan Memory ScanPress VFO 1 s Select band a or B Press MHz Tuning control 1 s Group ScanLocking Out a Memory Channel To quit Group Scan, press MHz again Setting Scan Limits Program ScanSelect the desired frequency as the lower limit Press F Using Program Scan Select the appropriate bandTo quit Program Scan, press VFO again To quit MHz Scan, press MHz again CALL/VFO Scan CALL/MEMORY ScanTo quit Call/VFO Scan, press Call again To quit Call/Memory Scan, press Call again Using Ctcss Continuous Tone Coded Squelch System CtcssPress the left or right Band SEL to select band a or B Press Tone to activate the Ctcss function Ctcss FREQ. ID Press Scan to activate the Ctcss Freq. ID Using DCS Digital Code Squelch DCSPress Tone to activate the DCS function DCS Code ID Press Scan to activate the DCS Code ID Manual Dialing Dtmf MonitorFreq. Hz 1209 1336 1477 1633 Turn the Tuning control to select a character Automatic DialerStoring a Dtmf Number in Memory Repeat steps 4 and 5 to enter up to 8 digits Transmitting a Stored Dtmf Number Selecting TX SpeedSelecting Pause Duration Programmable Function PF Keys PF PF1MR PF2 VFO PF3 Auxiliary Functions Press VFO Press Mic EnterPress the numeric keys in sequence on the keypad Changing Frequency Step Size Programmable VFOPress VFO Press F, Step Press c/ d to select the desired step size Auto Dimmer Change Display Contrast Adjust Display DimmerPOSITIVE/ Negative Reversal Blanking a Band Display Automatic Band Change A.B.C PWR switch MHz SQL controls VOL controls Press F, MHz to switch the function on or OFFTransceiver Lock Changing MULTI-FUNCTION Button Labels Meter Squelch Squelch Hang Time Changing Beep Volume Switching FM/AM ModeKEY Beep ON/ OFF Advanced Intercept Point AIP TIME-OUT Timer TOT Automatic Power OFF APO POWER-ON Message Display DemonstrationRepeat steps 3 and 4 to enter up to 8 digits Changing Speaker Configurations Connection Mode Band a Band BSpeaker Mute Changing TX/RX Deviation TM-D700E only Microphone Control with MC-53DM only Wireless Remote Control U.S.A./ Canada only Preparation Access Menu 1-A-3 Control and select on Control OperationSelect the receive frequency on band B UHF Digits Enter or VFO UP/ Down SKY Command 2 U.S.A./ Canada only Freq Connecting the Transporter with the HF Transceiver TM-D700A Preparation Flow 17 r On Commander Programming Call SignsProgramming a Tone Frequency On Transporter Mic Key Function RIT ON/ OFF XIT ON/ OFF T y Repeater Function U.S.A./ Canada only VS-3 Voice Synthesizer Optional Band SEL Optional Accessories PS-33 SP-50B VS-3 VC-H1PG-2N PG-3B PG-4X PG-5A MC-45 MC-53DM MC-80 MJ-88 MJ-89 Installing Options Installing the PG-4X Extension Cable KITRemove the 6 screws from the lower cover of the main unit Replace the lower cover 6 screws Connections Using One Set of PG-4X Kit Connections Using Two Sets of PG-4X Kits Maintenance ServiceService Note Cleaning Troubleshooting Problem Probable Cause Corrective Action COM Port Specifications VHF Band UHF Band Transmitter Sub VHF or UHF band Index