VFO Scan, Memory Scan, Press VFO 1 s | Kenwood TM-D700 E instruction

VFO SCAN

VFO Scan monitors all frequencies tunable on the band, using the current frequency step size.

MEMORY SCAN

Use Memory Scan to monitor all memory channels programmed with frequency data.

1 s

1 s

91 Select the desired band.

2 Press [VFO] (1 s).

•Scan starts at the frequency currently displayed.

•The 1 MHz decimal blinks while scanning is in progress.

•To reverse the scan direction, turn the Tuning control clockwise (upward scan) or counterclockwise (downward scan). You can also press Mic [UP]/ [DWN].

1Select band A or B.

2Press [MR] (1 s).

•Scan starts with the channel last recalled.

•The 1 MHz decimal blinks while scanning is in progress.

•To reverse the scan direction, turn the Tuning control clockwise (upward scan) or counterclockwise (downward scan). You can also press Mic [UP]/ [DWN].

3 To quit VFO Scan, press [VFO] again.

3 To quit Memory Scan, press [MR] again.

Note:

◆ At least 2 or more memory channels must contain data and must not be locked out.

◆ The L0 to L9 and U0 to U9 memory channels are not scanned.

◆ You can also start Memory Scan when in Channel Display mode. While Scan is being interrupted, the channel number blinks.

50

Image 56

Kenwood TM-D700 E instruction manual VFO Scan, Memory Scan, Press VFO 1 s, Select band a or B, Press MR 1 s

Contents

TM-D700A Models Covered by this Manual FeaturesThank YOU When condensation occurs inside the transceiver One or more of the following statements may be applicable Contents Selecting the Number of Channels Using Visual Scan Setting Scan Limits Using Program ScanRecalling the Call Channel Reprogramming the Call Channel Locking Out a Memory Channel Changing MULTI-FUNCTION Squelch Hang Time Supplied Accessories Conventions Followed in this Manual Preparation Mobile InstallationMain Unit Installation Front Panel Installation Slide the front panel down until its locking tab clicks Fixed Station Installation Modular Plug Cable Connection DC Power Cable Connection Mobile Operation Fixed Station Operation PS-33 20.5 A, 25% duty cycle Transceiver 15 a Supplied Accessory 20 a DC Power Cable Antenna ConnectionReplacing Fuses Fuse Location Fuse Current Rating Microphone Accessory ConnectionsExternal Speakers Your First QSO Ew wew w Getting Acquainted Front Panel 3SQL control GPS jack Main UNIT- FrontMain UNIT- Rear Microphone Indicators Basic Transceiver Modes Button Function Display Band a & B TX Band and Control BandTX Band Control Band MIC Keypad Direct Entry MC-53DM only Switching Power ON/OFF Adjusting VolumeSwitch on the DC power supply Operating Basics Adjusting Squelch Selecting a Frequency Transmitting Selecting Output PowerWhen you finish speaking, release Mic PTT Menu Access Press MNU to enter Menu modeMenu SET-UP Press c/ d to select the appropriate level 1 No Press OK Menu Configuration Level Selections Default Auto PM Channel Store Channel DisplayMemory Channel Lockout Memory channel name See reference Number Store Visual Scan Automatic Power Off APO Remote ControlMic PF Key See reference Mic MR Key Mic VFO Key See reference My call sign See reference Color for call sign WhiteMessage See reference Color for message RSV report See reference Color for RSV report Commander call sign See reference Transporter call sign Sky Command modeStatus text transmit rate See reference Packet path See reference Operating Through Repeaters Offset Programming Flow Programming Offset Selecting Offset DirectionSelecting Offset Frequency Press c / d to select Radio 1-, then press Activating Tone Function Selecting a Tone FrequencyPress Tone to activate the Tone function Press F, T.SEL Automatic Repeater Offset A. and Canada versions Transmitting a 1750 Hz Tone Automatic Simplex Check ASC Press REV to switch the Reverse function on or OFFReverse Function Tone FREQ. ID Press Scan to activate the Tone Freq. ID Parameter Simplex Odd-split Memory ChannelsSimplex & Repeater or ODD-SPLIT Memory CHANNEL? Select the desired transmit frequency Press M.IN Storing ODD-SPLIT Repeater FrequenciesPress M.IN 1 s Select band a or B Press MR to enter Memory Recall mode Press MHz Tuning control+ Power onRecalling a Memory Channel Clearing a Memory Channel Turn the Tuning control to select the first digit Naming a Memory ChannelPress a Repeat steps 6 and 7 to enter up to 8 digits Call Channel Recalling the Call ChannelReprogramming the Call Channel Press VFO MEMORY-TO-VFO Transfer Channel Display Partial or Full RESET? ParameterBand B 440.000 MHz Programmable Memory PM Programmable Information Application Examples Situationit ti Storing in PM Channels Recalling a PM Channel Auto PM Channel Store PM Channel ResetPress PM+ Power on Scan Scan Type Scan Range Mode 1 31 ch Mode 2 61 chVisual Scan Selecting the Number of Channels To quit Visual Scan, press ESC Using Visual ScanPress F, Visual to start Visual Scan Time-Operated mode Carrier-Operated modeSeek mode Selecting Scan Resume Method VFO Scan Memory ScanPress VFO 1 s Select band a or B Press MHz Tuning control 1 s Group ScanLocking Out a Memory Channel To quit Group Scan, press MHz again Select the desired frequency as the lower limit Press F Setting Scan LimitsProgram Scan Using Program Scan Select the appropriate bandTo quit Program Scan, press VFO again To quit MHz Scan, press MHz again CALL/VFO Scan CALL/MEMORY ScanTo quit Call/VFO Scan, press Call again To quit Call/Memory Scan, press Call again Using Ctcss Continuous Tone Coded Squelch System CtcssPress the left or right Band SEL to select band a or B Press Tone to activate the Ctcss function Ctcss FREQ. ID Press Scan to activate the Ctcss Freq. ID Press Tone to activate the DCS function Using DCSDigital Code Squelch DCS DCS Code ID Press Scan to activate the DCS Code ID Freq. Hz 1209 1336 1477 1633 Manual DialingDtmf Monitor Turn the Tuning control to select a character Automatic DialerStoring a Dtmf Number in Memory Repeat steps 4 and 5 to enter up to 8 digits Selecting Pause Duration Transmitting a Stored Dtmf NumberSelecting TX Speed Programmable Function PF Keys PF PF1MR PF2 VFO PF3 Press the numeric keys in sequence on the keypad Auxiliary FunctionsPress VFO Press Mic Enter Changing Frequency Step Size Programmable VFOPress VFO Press F, Step Press c/ d to select the desired step size POSITIVE/ Negative Reversal Auto Dimmer Change Display Contrast AdjustDisplay Dimmer Blanking a Band Display Automatic Band Change A.B.C PWR switch MHz SQL controls VOL controls Press F, MHz to switch the function on or OFFTransceiver Lock Changing MULTI-FUNCTION Button Labels Meter Squelch Squelch Hang Time Changing Beep Volume Switching FM/AM ModeKEY Beep ON/ OFF Advanced Intercept Point AIP TIME-OUT Timer TOT Automatic Power OFF APO Repeat steps 3 and 4 to enter up to 8 digits POWER-ON MessageDisplay Demonstration Changing Speaker Configurations Connection Mode Band a Band BSpeaker Mute Changing TX/RX Deviation TM-D700E only Microphone Control with MC-53DM only Wireless Remote Control U.S.A./ Canada only Preparation Access Menu 1-A-3 Control and select on Control OperationSelect the receive frequency on band B UHF Digits Enter or VFO UP/ Down SKY Command 2 U.S.A./ Canada only Freq Connecting the Transporter with the HF Transceiver TM-D700A Preparation Flow 17 r On Commander Programming Call SignsProgramming a Tone Frequency On Transporter Mic Key Function RIT ON/ OFF XIT ON/ OFF T y Repeater Function U.S.A./ Canada only VS-3 Voice Synthesizer Optional Band SEL Optional Accessories PS-33 SP-50B VS-3 VC-H1PG-2N PG-3B PG-4X PG-5A MC-45 MC-53DM MC-80 MJ-88 MJ-89 Installing Options Installing the PG-4X Extension Cable KITRemove the 6 screws from the lower cover of the main unit Replace the lower cover 6 screws Connections Using One Set of PG-4X Kit Connections Using Two Sets of PG-4X Kits Maintenance ServiceService Note Cleaning Troubleshooting Problem Probable Cause Corrective Action COM Port Specifications VHF Band UHF Band Transmitter Sub VHF or UHF band Index