KitchenAid KFGR364 Location requirements, Tools and parts needed for Portable installations

Models: KFGR382 KFGR364 KFGR270 KFGR274

1 48
Download 48 pages 3.13 Kb
Page 3
Image 3
Materials required:

The California Safe Drinking Water and Toxic Enforcement Act requires the Governor of California to publish a list of substances known to the State of California to cause cancer, birth defects, or other reproductive harm, and requires businesses to warn of potential exposure to such substances.

WARNING: This product contains a chemical known to the State of California to cause cancer, birth defects, or other reproductive harm.

This appliance can cause low-level exposure to some of the substances listed, including benzene, crystalline silica, carbon monoxide, toluene, and soot.

In the State of Massachusetts, the following installation instructions apply:

Installations and repairs must be performed by a qualified or licensed contractor, plumber, or gasfitter qualified or licensed by the State of Massachusetts.

If using a ball valve, it shall be a T-handle type.

A flexible gas connector, when used, must not exceed 3 feet.

Tools and parts needed for Built-in (non-combustible construction) installations

level

small flat-blade screwdriver

flat-blade screwdriver

Phillips screwdriver

tape measure or ruler

slip-joint pliers

pipe wrench

scissors or cutting pliers to remove tiedowns

Materials required:

gas line shutoff valve

1/2" male pipe thread nipple for connection to pressure regulator

L.P. gas-resistant pipe-joint compound

AGA or CSA design-certified outdoor flexible stainless steel appliance connector [4-5 ft. (1.2-1.5 m)] or rigid gas supply line as needed

non-corrosive leak detection solution

Parts supplied

convertible regulator is set for 4" W.C. natural gas.

Parts needed

The built-in grills are manufactured for use with natural gas.

To convert to L.P./propane gas, Gas Conversion Kit no. 4396311 must be used. Follow Instructions included with kit.

Tools and parts needed for Portable installations

level

small flat-blade screwdriver

flat-blade screwdriver

Phillips screwdriver

tape measure or ruler

slip-joint pliers

adjustable wrench

scissors or cutting pliers to remove tiedowns

Materials required:

non-corrosive leak detection solution

Parts supplied

hose and regulator assembly set for 11" W.C. L.P. gas (attached to manifold)

20 lb. L.P. tank (empty) – requires purging and L.P. gas fill by certified L.P. gas fill station

Parts needed

The portable grills are manufactured for use with L.P./Propane gas.

To convert to Natural gas, Gas Conversion Kit no. 4396312 must be used. Instructions included with kit.

To connect to a fixed L.P./propane gas supply, you must purchase Convertible Regulator Kit No. 4396424 from your dealer.

Location requirements

Parts suppliedWARNING

Explosion Hazard

Do not store fuel tank in a garage or indoors.

Do not store grill with fuel tank in a garage or indoors.

Failure to follow these instructions can result in death, explosion, or fire.

Parts neededWARNING

Fire Hazard

Do not use grill near combustible materials.

Do not store combustible materials near grill.
Doing so can result in death or fire.

Select a location that provides minimum exposure to wind and traffic paths. The location should be away from strong draft areas.

Do not obstruct flow of combustion and ventilation air.

The built-in grills are manufactured for use with natural gas.WARNING

Fire Hazard
Do not install this grill on or near combustible materials.

Doing so can result in death or fire.

If you plan to use a combustible enclosure,

return this unit and replace it with the model which is manufactured for use in a combustible enclosure.

Clearance to combustible construction for built-in (non-combustible construction) and portable grills:

A minimum of 12" (30.5 cm) must be maintained between the grill hood, sides and back and any combustible construction. A 12" (30.5 cm) minimum clearance must also be maintained below the cooking surface and any combustible construction.

Rotisserie

If your model is equipped with a rotisserie, 6" (15.2 cm) minimum clearance on each end is needed for the motor and skewer.

A grounded, 3-prong outlet located to the left of the grill is required. (See “Electrical requirements” section.)

3

Page 3
Image 3
KitchenAid KFGR364 Location requirements, Tools and parts needed for Portable installations, Parts supplied, Parts needed