Parameters
Hold Uppr Ctrl (Hold Upper Controller)
[Off, Pedal 1/(Pdl1)*, Pedal 2/(Pdl 2)*]
This is displayed in Normal Edit mode.
Pedal 1: A pedal switch etc. connected to the rear panel ASSIGNABLE PEDAL/SW 1 jack will switch Hold on/off for the notes played on the keyboard that controls the UPPER tone generator.
Pedal 2: A pedal switch etc. connected to the rear panel ASSIGNABLE PEDAL/SW 2 jack will perform the above operation.
Off: No function.
Hold Lowr Ctrl (Hold Lower Controller)
[Off, Pedal 1/(Pdl1)*, Pedal 2/(Pdl 2)*]
This is displayed in Normal Edit mode.
Pedal 1: A pedal switch etc. connected to the rear panel ASSIGNABLE PEDAL/SW 1 jack will switch Hold on/off for the notes played on the keyboard that controls the LOWER tone generator.
Pedal 2: A pedal switch etc. connected to the rear panel ASSIGNABLE PEDAL/SW 2 jack will perform the above operation.
Off: No function.
Wheel Brk Ctrl (Wheel Brake Controller)
[Off, Pedal 1/(Pdl1)*, Pedal 2/(Pdl 2)*]
This is displayed in Normal Edit mode.
Pedal 1: A pedal switch etc. connected to the rear panel ASSIGNABLE PEDAL/SW 1 jack will switch the “Wheel Brake” parameter (Global mode Group 7) on/off.
Pedal 2: A pedal switch etc. connected to the rear panel ASSIGNABLE PEDAL/SW 2 jack will perform the above operation.
Off: No function.
Wheel Brk Pedal (Wheel Brake Pedal Mode)
[Momnt, Alter]
Select the on/off operation of the pedal switch etc. connected to the rear panel ASSIGNABLE PEDAL/SW 1 or 2 jack.
Momnt: The pitch will gradually fall as long as you continue pressing the pedal switch. When you release the pedal switch, the pitch will gradually rise to the normal state.
Alter: The pitch will begin falling once you press the pedal switch. When you press it once again, the pitch will gradually rise to the normal state.
Rtry FAST Ctrl (Rotary FAST Controller)
[Off, Pedal 1/(Pdl1)*, Pedal 2/(Pdl 2)*]
Pedal 1: A pedal switch etc. connected to the rear panel ASSIGNABLE PEDAL/SW 1 jack will turn the ROTARY [FAST] key on/off.
Pedal 2: A pedal switch etc. connected to the rear panel ASSIGNABLE PEDAL/SW 2 jack will perform the above operation.
Off: No function.
Rtry FAST Pedal (Rotary FAST Pedal Mode)
[Momnt, Alter]
Select the on/off operation of the pedal switch etc. connected to the rear panel ASSIGNABLE PEDAL/SW 1 or 2 jack. The pedal switch will have the same function as pressing the front panel ROTARY [FAST] key.
Momnt: The rotary speed will gradually increase as long as you continue pressing the pedal switch, until it reaches the speed specified by the Group 6 “Rotor Fast Speed” parameter. When you release the pedal switch, the rotary speed will gradually decrease until it reaches the speed specified by the Group 6 “Rotor Slow Speed” parameter. Alter: Once you press the pedal switch, the rotary speed will gradually increase until it reaches the speed specified by the Group 6 “Rotor Fast Speed” parameter. When you press the pedal switch once again, the rotary speed will gradually decrease until it reaches the speed specified by the Group 6 “Rotor Slow Speed” parameter.
Rtry STOP Ctrl (Rotary STOP Controller)
[Off, Pedal 1/(Pdl1)*, Pedal 2/(Pdl 2)*]
Pedal 1: A pedal switch etc. connected to the rear panel ASSIGNABLE PEDAL/SW 1 jack will turn the ROTARY [STOP] key on/off.
Pedal 2: A pedal switch etc. connected to the rear panel ASSIGNABLE PEDAL/SW 2 jack will perform the above operation.
Off: No function.
Rtry STOP Pedal (Rotary STOP Pedal Mode)
[Momnt, Alter]
Select the on/off operation of the pedal switch etc. connected to the rear panel ASSIGNABLE PEDAL/SW 1 or 2 jack. The pedal switch will have the same function as pressing the front panel ROTARY [STOP] key.
Momnt: The rotary speed will gradually slow down and then stop as long as you continue pressing the pedal switch.
Alter: Once you press the pedal switch, the rotary speed will gradually slow down and then stop.
Amp Gain Ctrl (Amp Gain Controller)
[Off, Pedal 1/(Pdl 1)*, Pedal 2/(Pdl 2)*]
Pedal 1: An expression pedal etc. connected to the rear panel ASSIGNABLE PEDAL/SW 1 jack will control the Group 4 “Amp Gain” parameter of Normal Edit mode and EX Edit mode.
Pedal 2: An expression pedal etc. connected to the rear panel ASSIGNABLE PEDAL/SW 2 jack will perform the above operation.
Off: No function.
| * (Pdl 1), (Pdl 2): These indicate that Pedal 1 or Pedal 2 are selected for the Global mode Group 1 “Prog Up Ctrl” or “Prog Down Ctrl” parameters. With these settings, the settings of |
28 | Global mode are used, and the settings you made here will be ignored. However if you select another value in Global mode, the display here will change from (Pdl 1) to Pedal 1 or |
from (Pdl 2) to Pedal 2, and you will be able to operate the corresponding function from the pedal switch. | |
|
