108 mg/dL, Mmol/L | Lifescan Basic Blood Glucose Monitoring System

MESSAGE

APPEARS WHEN

wait

apply sample

45 .....0

108mg/dL

(Example)

61.mmol/L

(Example)

The meter is performing internal checks.

The meter is ready to receive a blood or control solution sample. If performing a check strip test, this is your signal to remove the check strip from the meter.

The meter is counting down from 45 seconds to 0.

A blood test has been completed. This indicates a blood glucose result when the meter is set for mg/dL.

A blood test has been completed. This indicates a blood glucose result when the meter is set for mmol/L, the unit of measure used in Canada and parts of Europe.

59

Image 67

Lifescan Basic Blood Glucose Monitoring System manual 108 mg/dL, Mmol/L

Contents

Basic Page Page Important The OneTouch Basic System kit contains Table of Contents Testing Your Blood Page Page Introduction Precautions Limitations Infection Control OneTouch Basic Blood Glucose Getting Started Complete OneTouch Basic Blood Glucose Monitoring System Basic Meter OneTouch Basic Blood Glucose Meter Test Strip HOLDER. The test strip Test Strip OneTouch Basic, Profile, OneTouch II Test Strips Important Test Strip Information To practice the test procedure, OneTouch Normal Control Solution Setting Meter Code Before TestingCode the OneTouch Basic Meter in these three easy steps Match the Code Numbers Press the On/Off Button Code the Meter Checking the System Checking with the Check Strip How to do a check strip test Page Example Checking with Control Solution Control solution test tips Do a control solution testSpot with the tip of the vial Important Control Solution Test Information Test strip in all How to do a control solution testPress On/Off Button. Insert Test Strip Spot facing up Control range You are ready to test your blood Apply Control Solution Control solution results Meter malfunction Extremes in testing temperatures Abbreviated Test Procedure Testing Your Blood Test Detailed Test Procedure Getting a Drop of Blood Penlet Plus Sampler, twist off the pro While the lancet is in the OneTouch Cock the OneTouch Penlet Plus Sampler Adjust the puncture depth setting Lance Your Finger Wash Your Hands Remove the Lancet Required blood volume. Proceed withYour blood glucose test Clockwise Always use caution when removing How to Test Your Blood Test strip. The test Remove a testStrip from the vial Replace the vial Cap immediately Do not touch Test spot on Apply Blood Sample Blood to the test Be sure that youTouch only the tip Drop After the result is displayed Accurate Results SecondsResults will appear without time Date. See Special Messages Checking the Amount of Blood on the Test Strip Remove the test If the following messageStrip from Back Take your meter with you to the lab Comparing Meter and Laboratory Results Example Comparing the resultsPage Entering the Memory Mode Using the Meter Memory Recalling Test Results Entering and Using Set-Up Mode Setting Meter Options If you want to change an option setting, use the C button Clock Time and Date Clock option is set to and when it is set to Setting the Time Setting the Date Or press the M button to move to the next option Beep Prompts Language Date Format Time Format Decimal Separator Unit of Measure Itself off after two minutes of no activity Exiting the Set-Up Mode Test Procedure Messages Solving Problems Button Solution test Mmol/L 108 mg/dL 80 mg/dL 100 mg/dL Alternating with 58 mg/dLAlternating with 58 mg/dL Hi mg/dL Error Messages Battry When this symbol is flashing, the batteries are too low Meter was used in very bright light Test New test strip Test strip was not inserted Test strip moved duringCorrectly New test strip 800 Error3 retest Not enough blood retest Test area may be dirty If appearing when you turnWas turned on Your meter on, your meter’s Repeat the test with a Last test failed after the countdown started Has not yet been coded Message when the meterMeter requires a test Strip vial to operate Taking Care Your Meter Keep the test strip holder and test area clean see Doing a Daily Check Cleaning the MeterAppears on the display Remove the Test Strip Holder from the Meter Wash only the test strip holder with Clean the Test Strip Holder Careful not to scratch the test area May also be used. Do not apply full Replace the Test Strip Holder Batteries should last about Replacing the Batteries To replace the batteries Door Remove the battery compartmentAgainst a hard surface Remove the batteries and reinsert them as illustrated References 15-35C SpecificationsDimensions 4.3 2.6 Weight 4.1 ounces with batteries Alkaline batteries Day Money-Back Guarantee Guarantee WarrantyThree-Year Warranty Page Index OneTouch Penlet Plus Adjustable Blood Page Page Page USA