Lincoln Electric C2.410 instruction

2.For multipass welds, deposit a first pass bead using a slight weave. We emphasize the importance of moving into the corner to assure penetration into the corner. Weld additional layers with a side-to-side weave hesitating at the sides long enough to melt out any small slag pockets and minimize undercut. Travel slow enough to maintain the shelf without spilling weld metal.

3.With this technique, slag spills down the weld. As long as no metal spills, operation is normal. Once welders are familiar with the EXX18 techniques, they will quickly learn to make sound welds of excellent appearance.

Horizontal Groove and Overhead Weld Techniques Weld with a series of first pass beads using a slight circular motion in the crater. Do not whip. Use 5/32” or smaller electrodes and currents in the lower portion of the electrode’s range.

3

	2	1	1
	2	3
		3
			2

-26-

Image 26

Lincoln Electric C2.410 manual

Contents

Stick Electrode Welding Guide Page Table of Contents Welding Procedures Out-Of-Position Welding Vertical and Overhead Vertical Up Techniques for Fillet and Groove Welds Vertical Up Groove Welds Vertical Down Welds Weld Vertical Up Fillet Welds160 Polarity High-Deposition Welding Jetweld LH-3800 E7028H8 Wrong End view Side view Corner Welds Jetweld 2 E6027 Amps. AC at 14/Min Groove WeldsGroove Welds First Pass Deep Groove Welds Joint a Pass E6011T Over E6011 Root Passes Ft. of Weld/Hr Lbs. of Elec./Ft. 049 Flat Fillet WeldsPlate Size T 14 ga 12 ga 10 ga No. of Passes Leg Size L 082 117 162 Weld Horizontal Fillet Welds Welding Inclined Plate 180 Downhill Angle degPolarity Arc Speed In./Min.3 Lbs. of Elec./Ft. High Speed Welding Sheet Metal AlternatePage Edge Welds Fillet Welds Lap Welds Current Amps 120 170 Polarity Diameter PositionCurrent Amps 110 155 Polarity 018 028 Burnthrough Spot Welds Roof Decking to Beam Roof Beam Flange Roof Deck Thickness 22 ga 20 ga 18 ga 16 ga Low Hydrogen Welding E7018-1 Multipass Page Overhead Groove Welds Diameter Current Amps 155 Polarity Arc Speed In./Min Ft. of Weld/Hr Lbs. of Elec./Ft. Overhead Fillet Welds Also see Out-of Position Procedures,No. of Pass Leg Size L No. of Passes Leg Size L Diameter Current Amps 230 200 Polarity Horizontal Groove WeldsBack gouge first bead as needed Plate Size T No. of Passes Arc Speed In./Min Ft. of Weld/Hr Lbs. of Elec./Ft. of Weld Use steel backing as on 230 200 Polarity With E7028 Electrode 132 195 272 409 727 With E7018 Electrode275 350 260 335 157 236 320 785 Ft. of Weld/Hr.2 Lbs. of Elec./Ft.203 335 Minimum Preheat and Interpass Temperature1 Stick Electrode Typical Operating Procedures Out-of-Position Group High Deposition Group High Speed Group Low Hydrogen Group Low Hydrogen, Low Alloy Steel Group Fleetweld Fleetweld 35LS Jetweld Shield-Arc 70+ Fleetweld JetweldFleetweld 5P Shield-Arc Fleetweld 5P+ Shield-Arc HYP+ Electric Shock can kill Fumes and Gases can be dangerous For Electrically powered Electric and Magnetic Fields Stick C2.410 12/04