Lincoln Electric IM586-B manual K1758-L Input Cable Assem BLY, K2147 Control Cable and Weld Cable

C-2 ACCESSORIES C-2

K1758-”L” INPUT CABLE ASSEM-

BLY

Consists of an 8-conductor control cable with a 14-pin plug, a 6-conductor control cable with a 10-pin plug, and an electrode cable with Twist-Mate™ connector. It is rated at 300 amps, 60% duty cycle and is avail- able in lengths of 10 ft. (3 mm), 25 ft. (7.6 m), and 50 ft. (15 m).

K2147 CONTROL CABLE AND WELD CABLE

Consists of an 8-conductor control cable with a 14-pin plug, a 6-conductor control cable with a 10-pin plug, and a co-axil weld cable. It is rated at 300 amps, 60% duty cycle and is available in lengths of 75 ft. (22.6m), 100 ft. (30m).

K659-1 GAS GUARD REGULATOR

Adjustable flow regulator with removable adjustor key for CO2 and Argon blend gases. Mounts onto wire drive gas inlet, and reduces gas waste and arc start "blow" by reducing surge caused by excess pressure in supply hose.

K590-4 WATER CONNECTION KIT

(For 10 Series Wire Drive Only)

Install per the instructions shipped with the kit.

Also, the Module provides for interface connection of external equipment (fume extractor, etc.) to the Moduleʼs isolated relay contacts which actuate when the feeder welding gas solenoid is activated (repre- senting welding operation in process).

K1561-1 ROBOTICS INTERFACE MODULE

The module plugs directly into the STT-10 control board and provides an interface to a properly equipped Fanuc robot. (ArcTool software and an addi- tional process I/O board are needed). When installed and properly configured, the K1561-1 Robotics Interface Module allows complete control of the weld- ing process form the robot controller.

The Lincoln Electric Companyʼs Automation Center should be contacted for questions regarding installa- tion or operation of the Robotics Interface Module.

K1557-1 SWIVEL MOUNT

The K1557-1 Swivel mount attaches to the power source. This kit includes a feeder adapter plate that allows the feeder to rotate on top of the power source. The feeder can be easily separated from the swivel mount at any time. This option is compatible with the K1556-1 Light Duty Caster Kit.

K682-2 WATER CONNECTION KIT

(K679 Synergic 7F Wire Drive Only)

Install to either side of wire feed unit mounting bracket per instructions shipped with the kit.

K683-1 DUAL PROCEDURE SWITCH

-Requires K686-2 Adapter for STT-10. Kit includes gun switch, and mountings for Lincoln Innershield and Magnum guns, with 15 ft. (4.5 m) control cable and 3- pin plug. K686-2 Adapter permits 3-pin plug and 5-pin gun trigger plug to be connected to STT-10 5-pin Trigger/Dual Procedure receptacle.

K1556-1 LIGHT DUTY CASTER KIT

This option provides 4 casters and all required hard- ware to mount it to the Power Feed 10. This option is compatible with the K1557-1 Swivel Mount.

K1555-1 INSULATED LIFT HOOK

For applications where an insulated lift hook is required. This kit provides an easily installed, heavy duty insulated lift eye that mounts to the wire reel stand mast. See the instructions provided with the kit for installation.

K683-3 DUAL PROCEDURE SWITCH

Kit includes gun switch, and mountings for Lincoln Innershield and Magnum guns, with 15 ft. (4.5m) con- trol cable and 5-pin plug with two leads to connect to gun trigger.

K1558-1 REMOTE SWITCH INTERFACE MODULE

The Module provides for user interface connection of an external switch (flow switch, etc.) which must be closed to enable the feeder welding operation.

SPINDLE ADAPTERS:

K162H (Not required for STT-10 Bench Models) Spindle for boom mounting Readi-Reels and 2" (51

mm)I.D. spools with 60 lb. (27.2 kg) capacity. User mounted to appropriately prepared boom framework. Includes an easily adjustable friction brake for control of overrun.

When a 2" (51 mm) spindle is used with Readi-Reels or coils not on 12" (305 mm) O.D. spools, an adapter is required:

STT-10