Lincoln Electric SVM192-A Vehicle Mounting, Fuel Gasoline Fuel Only, 656-820 m, Installation

GASOLINE can cause fire or explosion.

A-4 INSTALLATION A-4

Return to Master TOC

3.Proper placement of the equipment on the trailer to insure stability side to side and front to back when being moved and when standing by itself while being operated or serviced.

4.Typical conditions of use, i.e., travel speed; rough- ness of surface on which the trailer will be operated; environmental conditions.

5.Conformance with federal, state and local laws(1)

(1)Consult applicable federal, state and local laws regarding specif- ic requirements for use on public highways.

OIL

LUBRICATION SYSTEM CAPACITY

(INCLUDING FILTER)

Kohler CH23S - 2.0 Quarts (1.9 Liters)

The EAGLE 10,000 is shipped with the engine crankcase filled with SAE 10W-30 oil. Check the oil level before starting the engine. If it is not up to the full mark on the dip stick, add oil as required. Make certain that the oil filler cap is tightened securely. Refer to the engine Owner’s Manual for specific oil recommenda- tions.

Return to Section TOC

Return to Section TOC

Return to Master TOC

WARNING

VEHICLE MOUNTING

Improperly mounted concentrated loads may cause unstable vehicle handling and tires or other components to fail.

•Only transport this Equipment on serviceable vehicles which are rated and designed for such loads.

•Distribute, balance and secure loads so vehicle is stable under conditions of use.

•Do not exceed maximum rated loads for components such as suspension, axles and tires.

•Mount equipment base to metal bed or frame of vehicle.

•Follow vehicle manufacturer’s instructions.

------------------------------------------------------------------------------------------

CAUTION

READ the engine operating and maintenance instructions supplied with this machine.

CAUTION

BATTERY CONNECTIONS

Use caution as the electrolyte is a strong acid that can burn skin and damage eyes.

------------------------------------------------------------------------------------------

This welder is shipped with the negative battery cable discon- nected. Make sure that the Engine Switch is in the “OFF” posi- tion and attach the disconnected cable securely to the negative battery terminal before attempting to operate the machine. If the battery is discharged and does not have enough power to start the engine, see the battery charging instructions in the Battery section.

NOTE: This machine is furnished with a wet charged battery; if unused for several months, the battery may require a booster charge. Be careful to charge the battery with the correct polarity.

WELDING OUTPUT CABLES

Return to Section TOC

Return to Master TOC

WARNING

•Stop engine while fueling.

•Do not smoke when fueling.

• Keep sparks and flame away from tank.

• Do not leave unattended while fueling.

• Wipe up spilled fuel and allow fumes to clear before starting engine.

• Do not overfill tank, fuel expansion may cause overflow.

--------------------------------------------------------------------------------

With the engine off, connect the electrode and work cables to the studs provided. These connections should be checked periodi- cally and tightened if necessary. Loose connections will result in overheating of the output studs.

When welding at a considerable distance from the welder, be sure you use ample size welding cables. Listed below are cop- per cable sizes recommended for the rated current and duty cycle. Lengths stipulated are the distance from the welder to work and back to the welder again. Cable sizes are increased for greater lengths primarily for the purpose of minimizing cable volt- age drop.

Return to Section TOC

Return to Master TOC

FUEL (GASOLINE FUEL ONLY)

Fil the fuel tank with clean, fresh, lead-free gasoline. Observe fuel gauge while filling to prevent overfilling.

WARNING

• Damage to the fuel tank may cause fire or explosion. Do not drill holes in the EAGLE 10,000 base or weld to the EAGLE 10,000 base.

-----------------------------------------------------------------------

TOTAL COMBINED LENGTH OF ELECTRODE AND WORK CABLES

	225 Amps
	100% Duty Cycle
0-100 Ft.	1 AWG
(0-328 m)
100-200 Ft.	1 AWG
(328-656 m)
200-250 Ft.	1/0 AWG
(656-820 m)

EAGLE™ 10,000