iii

iii

SAFETY

Return to Master TOC

Return to Master TOC

Return to Master TOC

WELDING SPARKS can cause fire or explosion.

6.a. Remove fire hazards from the welding area. If this is not possible, cover them to prevent the welding sparks from starting a fire. Remember that welding sparks and hot

materials from welding can easily go through small cracks and openings to adjacent areas. Avoid welding near hydraulic lines. Have a fire extinguisher readily available.

6.b. Where compressed gases are to be used at the job site, special precautions should be used to prevent hazardous situations. Refer to “Safety in Welding and Cutting” (ANSI Standard Z49.1) and the operating information for the equipment being used.

6.c. When not welding, make certain no part of the electrode circuit is touching the work or ground. Accidental contact can cause overheating and create a fire hazard.

6.d. Do not heat, cut or weld tanks, drums or containers until the proper steps have been taken to insure that such procedures will not cause flammable or toxic vapors from substances inside. They can cause an explosion even though they have been “cleaned”. For information, purchase “Recommended Safe Practices for the Preparation for Welding and Cutting of Containers and Piping That Have Held Hazardous Substances”, AWS F4.1 from the American Welding Society (see address above).

6.e. Vent hollow castings or containers before heating, cutting or welding. They may explode.

6.f. Sparks and spatter are thrown from the welding arc. Wear oil free protective garments such as leather gloves, heavy shirt, cuffless trousers, high shoes and a cap over your hair. Wear ear plugs when welding out of position or in confined places. Always wear safety glasses with side shields when in a welding area.

6.g. Connect the work cable to the work as close to the welding area as practical. Work cables connected to the building framework or other locations away from the welding area increase the possibility of the welding current passing through lifting chains, crane cables or other alternate circuits. This can create fire hazards or overheat lifting chains or cables until they fail.

6.h. Also see item 1.c.

CYLINDER may explode if damaged.

7.a. Use only compressed gas cylinders

containing the correct shielding gas for the process used and properly operating regulators designed for the gas and

pressure used. All hoses, fittings, etc. should be suitable for the application and maintained in good condition.

7.b. Always keep cylinders in an upright position securely chained to an undercarriage or fixed support.

7.c. Cylinders should be located:

Away from areas where they may be struck or subjected to physical damage.

A safe distance from arc welding or cutting operations and any other source of heat, sparks, or flame.

7.d. Never allow the electrode, electrode holder or any other electrically “hot” parts to touch a cylinder.

7.e. Keep your head and face away from the cylinder valve outlet when opening the cylinder valve.

7.f. Valve protection caps should always be in place and hand tight except when the cylinder is in use or connected for use.

7.g. Read and follow the instructions on compressed gas cylinders, associated equipment, and CGA publication P-l, “Precautions for Safe Handling of Compressed Gases in Cylinders,” available from the Compressed Gas Association 1235 Jefferson Davis Highway, Arlington, VA 22202.

FOR ELECTRICALLY powered equipment.

8.a. Turn off input power using the disconnect switch at the fuse box before working on the equipment.

8.b. Install equipment in accordance with the U.S. National Electrical Code, all local codes and the manufacturer’s recommendations.

8.c. Ground the equipment in accordance with the U.S. National Electrical Code and the manufacturer’s recommendations.

Return to Master TOC

Mar ‘95

Page 4
Image 4
Lincoln Electric SVM 110-A service manual Cylinder may explode if damaged

SVM 110-A specifications

The Lincoln Electric SVM 110-A is a state-of-the-art welding machine designed to cater to the needs of professionals and hobbyists alike. Known for its adaptability and superior performance, the SVM 110-A provides a seamless welding experience that is gaining popularity across various industries.

One of the main features of the Lincoln Electric SVM 110-A is its impressive power output. Capable of delivering up to 110 amps of welding current, this machine is ideal for a wide range of applications, including light to medium fabrication work, maintenance, and repair tasks. The versatile voltage input options allow users to operate the machine on standard household current as well as generator power, enhancing its portability and usability in diverse settings.

The SVM 110-A employs advanced inverter technology, which allows for a more compact design without sacrificing performance. This technology not only improves efficiency but also provides greater control over the welding arc, ensuring cleaner beads and reduced spatter. Additionally, the inverter design contributes to a lighter weight, making the SVM 110-A easy to transport and maneuver.

Another significant characteristic of the SVM 110-A is its user-friendly interface. With intuitive controls and clear display indicators, the machine is designed for ease of use, enabling welders to quickly adjust settings to suit their specific needs. This feature is especially beneficial for beginners who are looking to enhance their skills without being overwhelmed by complex operations.

The machine supports a variety of welding processes, including MIG and stick welding, offering unmatched versatility in terms of the types of materials it can handle. From steel to aluminum, the SVM 110-A demonstrates excellent compatibility with various consumables, allowing users to select the best options for their projects.

Furthermore, the design of the SVM 110-A incorporates advanced safety features, including thermal overload protection and a sturdy construction that can withstand demanding environments. This commitment to safety ensures that users can perform their work confidently and efficiently.

In conclusion, the Lincoln Electric SVM 110-A is a remarkable welding machine that combines power, portability, and ease of use. Its advanced inverter technology, user-friendly controls, and versatility make it an ideal choice for both amateurs and seasoned welders. Whether for home projects or professional trades, the SVM 110-A stands out as a reliable and efficient solution in today’s welding landscape.