STRIP 1/2"1/2" (13MM)

FROM WIRE

TO BE ATTACHED.

 

INSERT TWISTED WIRES

 

UNDER TERMINAL AND

 

TIGHTEN. CHECK FOR

TWIST WIRES

A GOOD MECHANICAL

 

TOGETHER WITH

CONNECTION.

 

PLIERS (MINIMUM

 

OF THREE TURNS)

 

FIG. 60 Wire Termination for E-Bus Connection

1.Strip 1/2 in. (13 mm) insulation from the conductor.

2.

Insert the

wire

in the

required

terminal location

 

and tighten

the

screw to

complete

the termination.

3.If two or more wires are being inserted into one terminal location, twist the wires together a minimum of three turns before inserting them.

4.Cut the twisted end of the wires to 3/16 in. (5 mm) before inserting them into the terminal and tightening the screw.

5.Pull on each wire in all terminals to check for good mechanical connection.

Wire Requirements

The minimum type and grade of wire required to “network” the Intelli-Fin to other units or LonMark® devices is a Level IV, 22 AWG (0.034 mm2) plenum or non-plenum rated (as applicable), unshielded, twisted pair, stranded communication wire. The following manufacturers supply communication wire that meets or exceeds this specification for E-Bus connections.

Anixter

(847) 677-2600

 

www.anixter.com

__________________________________________________

Belden Wire and Cable Co.

(800) 235-3361

 

www.belden.com

__________________________________________________

BICC General

(800) 424-5666

 

www.biccgeneral.com

(BICC Cable, Brand-Rex, General Cable, Carol Cable)

__________________________________________________

ConnectAir International

(800) 247-1978

 

www.connect-air.com

__________________________________________________

Eastman Wire & Cable

(800) 257-7940

 

www.eastmanwire.com

__________________________________________________

Honeywell Inc.

(800) 345-6770

 

www.honeywell.com

__________________________________________________

Lucent Technologies

(305) 569-3600

 

www.lucent.com/netsys/

 

systimax

__________________________________________________

Windy City Wire

(800) 379-1191

www.smartwire.com

__________________________________________________

NOTE:

The minimum specification for Level IV, 22 AWG (0.034 mm2) unshielded, twisted pair, stranded communication cable must be plenum-rated when the wire is routed through air ducts or plenum areas. Non-plenum rated communication cable is for general use when the wire is not being routed through air ducts or plenum areas.

ADDITIONAL COMPONENTS

USED TO INTERFACE

MULTIPLE APPLIANCES

Serial LonTalk® Adapter (SLTA) — A serial LonTalk® adapter is required to provide communication between the E-Bus and either a PC serial port or an approved modem using the SLTA-10EIA-232 port. The SLTA interfaces with LonSpecTM software. There are specific null modem cable requirements for proper connection to a modem. The SLTA has a DB-9 female connection. Direct connection to a PC can be made with a DB-9 to DB-9 cable or a DB-9 to DB-25 cable, based on the available PC connection.

FTT Repeater — A repeater is available to increase the network wiring length in an E-Bus network. The repeater is designed to be installed in a standard field supplied 4 by 4 junction box.

Excel 15 — The Excel 15 Building Manager is a LonMark® compliant device that provides network management functions for the E-Bus in a Light Commercial Building Solutions System. The Excel 15 is compatible with the E-Bus and uses the free topology transceiver (FTT). Individual Excel 15 Controllers and Communicating Subbases distributed on the E-Bus perform specific HVAC equipment control. The Excel 15 monitors and controls both local and remote controller points. If E-Bus communications are interrupted, the Excel 15 is capable of stand-alone operation.

47

Page 47
Image 47
Lochinvar 000, 1 warranty Additional Components Used to Interface Multiple Appliances, Wire Termination for E-Bus Connection

000, 000 through 2, 1 specifications

Lochinvar 1 is a remarkable achievement in the realm of modern technology and engineering. As a powerful and efficient water heater, it has been designed to cater to a wide range of residential and commercial needs. One of the standout features of Lochinvar 1 is its advanced heating technology, which incorporates a high-efficiency condensing design. This technology allows the unit to achieve impressive energy savings by maximizing heat transfer while minimizing energy consumption.

The Lochinvar 1 utilizes a stainless steel heat exchanger that enhances durability and corrosion resistance. This not only extends the lifespan of the unit but also ensures consistent performance over time. Coupled with a user-friendly control system, users can easily adjust settings and monitor performance, enhancing overall convenience and usability.

Another key characteristic of the Lochinvar 1 is its compact design, making it suitable for a variety of installation environments. Whether in a residential basement or a commercial utility room, the unit’s space-saving configuration allows for efficient use of available area without compromising on capability.

Safety features are integral to the Lochinvar 1, providing peace of mind for users. The unit is equipped with advanced monitoring systems that can detect irregularities and automatically shut down the system if necessary. This not only protects the equipment but also enhances the safety of the environment in which it operates.

In terms of performance, Lochinvar 1 boasts a high recovery rate, ensuring hot water is available on demand. This is particularly beneficial for settings with high water usage, allowing simultaneous operations without lag.

Moreover, the unit supports various venting options, offering flexibility during installation. Whether using traditional vertical venting or innovations like direct venting, Lochinvar 1 accommodates different building designs and local codes, making it highly versatile.

In conclusion, Lochinvar 1 epitomizes the melding of efficiency, reliability, and user-friendly technology. With its high-performance features, robust safety systems, and adaptable installation options, it stands out as a forefront player in the water heating industry, meeting the diverse needs of today's consumers and businesses alike.