Manuals / Lowrance electronic / Marine Equipment / SONAR

Lowrance electronic X52, X59DF manual

Models: X52 X59DF

1 84

Download 84 pages 43.34 Kb

<>

Troubleshooting Install Chart Speed Alarms Symbols with FishTrack depths Reset Options Other Accessories Main Menu Commands To adjust sensitivity To Restore Factory Settings

Page 34

Notes

30

Page 33 Page 35

Image 34

Lowrance electronic X52, X59DF manual

Page 33 Page 35

Contents

X52 and X59DF Lowrance Electronics Inc 12000 E. Skelly Dr Tulsa, OK USA Table of Contents Fish I.D. Fish Symbols & Depths Capabilities and Specifications X52 and X59DF IntroductionFeet 244 meters at 200 kHz 1500 feet Transducer Installation PreparationsSingle-frequency trolling motor installations Single-frequency transom installationsDual-frequency transom installations Shoot-through hull installationsPad Deadrise less than Strakes Good location Poor location Location Poor angleTransom Transducer centerline Hull bottom Dot Ratchet Ratchets Lock washer Bolt Nut Flat washer Metal Nut washer Rubber Washers Metal washer BoltTransom Bottom Hull Flat-bottom hull Deep-vee hull Internal tooth washer Trolling Motor Bracket InstallationBolt Nut Partial fish arches Transducer aimedShoot-Thru-Hull Preparation True bottom Second bottom Manual range setting Transducer location High speed Trolling speedShoot-Thru-Hull Installation Epoxy transducer to hull Speed/Temperature Sensors Good location Power ConnectionsTransom Bottom of hull Powering a Nmea 2000 Buss Nmea 2000 Power cable Page Power connections for the units in this series Nmea 0183 Cable Connections Nmea 2000 Cable ConnectionsTo Nmea To sonar Network port Units Network Socket Mounting the Unit Bracket, In-Dash or Portable Front 136 61.3 132 23.8 147.4 Millimeter Inch Hole Diameter 121Inches 112 Cut on line Other Accessories Page Basic Sonar Operation Memory MenusMain Menu Commands Sonar Menu Commands Pages Page Page Basic Sonar Quick Reference Sonar Operations Bait School Thermocline With fish Fish ArchesTo adjust sensitivity To Restore Factory Settings Important TipOther Free Training Aids Advanced Sonar Options & Other Features ASP Advanced Signal ProcessingAlarms To adjust and turn on the shallow alarmTo adjust and turn on the deep alarm To turn the fish alarm onBacklight Level Chart SpeedCalibrate Speed Grayline Contrast Thin or no Grayline Wider GraylineDepth Cursor Cursor line Depth boxDepth Range Manual To switch to Manual Depth RangeDepth Range Automatic To turn Auto Depth Range on againDepth Range Upper and Lower Limits Area zoomedFish I.D. Fish Symbols & Depths FasTrackPress ↓ to Fish ID Symbolsentexitexit FishTrackNoise Rejection Symbols with FishTrack depthsHyperScroll Overlay DataTo turn off displayed data Ping Speed & HyperScroll To change displayed data font sizeFrom the Sonar Page, press MENU↓ to Ping Speedent Reset Options Pop-up HelpScreen Contrast and Backlight Level Reset Water DistanceSensitivity & Auto Sensitivity Automatic Sensitivity Set Keel Offset Software Version Information Set LanguagePress MENUMENU↓ to SET Keel Offsetent Sonar Page & Sonar Chart Display Options Sonar Chart ModePress MENUMENU↓ to Software Infoent Split Zoom Sonar Chart Digital Data/Chart Stop Chart Sonar SimulatorSurface Clarity Units of Measure Press ↓ or ↑ to select clarity levelEXITEXITEXITUpper and Lower Limits VolumeZoom & Zoom Bar Zoom Pan Troubleshooting No fish arches when the Fish I.D. feature is off Noise Page Index Page Lowrance Electronics Full ONE-YEAR Warranty How to Obtain Service… Accessory Ordering Information for all countries Visit our web site