Manuals / Macurco / Household Appliance / Carbon Monoxide Alarm

Macurco DVP-120 operating instructions R e l a y

Models: DVP-120

1 37

Download 37 pages 45.49 Kb

Page 26

R e l a y

3.3.4 Configure Relays, Horn & Strobe Submenu

There is a list of parameters for each relay in the system. The left and right cursor keys can be used to move from one relay, horn or strobe to another. Doing so always goes to the first (summary) display. The up and down keys will scroll through the parameters for the particular relay, horn or strobe.

3.3.4.1 Relay Summary

R e l a y	1 N o r m . O f f
D e l a y	O n , M i n . O n

Figure 3-29 Relay Summary

This display example shows that Relay 1 is configured to operate Normally Off, with a turn on delay and a minimum on time.

Notice that the relay number, 1 in this example, is underlined. This indicates that the digit keys can be used to jump to a particular relay, horn or strobe. The relays are numbers 1, 2 and 3; the horn is number 4 and the strobe is 5.

3.3.4.2 Relay Mode

R e l a y 1 N o r m . O f f

M o d e : 2

Figure 3-30 Relay Mode

This display example shows that relay 1 is configured to operate in the Normally Off mode. The relay modes are:

– 1 ALARM

–2 Normally Off (default)

–3 Normally On

Relay mode 1 is a special case. This mode is only available on relay 1 and dedicates the relay to function as an alarm signal to a subsequent alarm or monitoring panel. This mode forces the relay to normally off mode with no turn on delay or minimum on time. See section 3.1.4 for more detail regarding alarms

Fail Safe operation can be implemented by configuring a relay to operate Normally On, and wiring the circuit using the NC (normally closed) contact. In this way, if the control panel looses power the relay will turn on the controlled device if it still has power.

3.3.4.3 Relay Turn On Delay

R e l a y 1 D e l a y	O n
( m m : s s ) 0 1 : 0 0

Figure 3-31 Turn On Delay

The default turn on delay is one minute and the maximum allowed value is fifteen minutes. The value is entered in two groups, 2 digits for the minutes and then 2 digits for the seconds. A leading zero must be entered for each group if applicable.

3.3.4.4 Relay Minimum On Time

R e l a y 1 ( m m : s s )

M i n . O n 0 1 : 0 0

Figure 3-32 Minimum on time

The default minimum on time is one minute and the maximum allowed value is fifteen minutes.

Revision 0.07

26

Image 26

Macurco DVP-120 operating instructions R e l a y

Contents

DVP-120Installation & Operating Instructions TABLE OF CONTENTS Figure 3-12Zone Signal display Figure 3-6Alarm displayFigure 3-7Alarm Silenced message Figure 3-13Zone Signal Silenced messageTable 2-3Connector to Sensor Channel Mapping Table 2-1Main Power ConnectionsTable 2-2Recommended Wire Gauge Relay Interface Signals and Connector Assignments1.1General Information 1INTRODUCTION1.2Features 1.3Compatible Macurco TransducersMain Fan Power Figure 1-1System Wiring DiagramENGINEER AND ARCHITECT SPECIFICATIONS MACURCO DVP-120Figure 1-2 DVP-120Internal View Revision1.6Return Instructions Specifications1Warranty 2.1Mounting the DVP-120 2 Installation & Connection2.2General Wiring Information Figure 2-1Sensor Interface Connector 2.3Main power ConnectionTable 2-1Main Power Connections Table 2-2Recommended Wire GaugeTable 2-3Connector to Sensor Channel Mapping Figure 2-2Relay Connector 2.5Relay Connection2.6Horn & Strobe Connection Figure 2-3Horn & Strobe ConnectorTable 2-7Wire gauge for Horn & Strobe functions 2.7Interfacing Macurco Sensors Table 2-8Macurco TransducersD V P 3 OperationDVP - 1 2 0 V e r V e r3.1.2 User Interface Figure 3-3Keypad layoutO F F Figure 3-6Alarm displayMO N 1 0 2 3 R S 0 1C OWA R N I N G C O S E N S O R Figure 3-7Alarm Silenced messageA L A R M S I L E N C E D F O R 5 M I N U T E S WA R N I N G F O RT R O U B L E S I L E N C E D F O R 8 H O U R S Figure 3-12Zone Signal displayFigure 3-13Zone Signal Silenced message Z O N ES E N S O R S F O U N D 3.3Setting the System ConfigurationFigure 3-15Save Configuration? Prompt R E L A Y S F O U N DT i m e 1 6 5 D a y T u e s d a y T i m e 2 2 5 D a y T u e s d a yT i m e 0 1 5 D a y T u e s d a y Figure 3-16Set Time of Day1L o a d D e f a u l t C o n f i g u r a t i o n Figure 3-20Load Default ConfigurationT i m e 2 2 5 D a y 2T u e s d a y Figure 3-19Set Day of the weekFigure 3-23Wrong Password Prompt Figure 3-21Enter PasswordFigure 3-22Password Prompt P a s s w o r dS e n s o S e n s o r S e n s o rW a r n i n g 5 0p p m R a n g eR e l a y H o r n S t r o b e 5N o r m . O f f D e l a y O n S e n s o r T y p e Z o n e 1 C o n t r o l s R 1R 2R 3H 4SG r o u p Figure 3-41Zone ControlsZ 1 G r o u p D a y s Z 1 G r o u p Figure 3-54Horn Alarm Signal Figure 3-52Alarm SignalsFigure 3-53Buzzer Alarm Signal A l a r m S i g n a l sa r m S i g n a l s Figure 3-61Buzzer Trouble Signal Figure 3-59Strobe Warning SignalFigure 3-60Trouble Signals Figure 3-62Horn Trouble Signall e S i g n a l s Figure 3-63Strobe Trouble SignalT r o u b S t r o b e4.1System Status Light Flashing 4 Troubleshooting4.2Timed ventilation problem 4.4LCD Display unreadable 4.3No Power4.6After a power failure