ENGLISH
⁄3 CONTROL buttons
These buttons are used when operating PLAY, STOP, PAUSE and other commands of a source.
(When TUNER mode is selected)
T.DISP button
Used to select the display mode in RDS.
PTY button
Used to display the programme type information of the current station.
F.DIRECT button
Used to select the "Frequency direct input".
PRESET +/- buttons
Used to select a preset station up and down.
TUNING +/- buttons
Used to tune a frequency station up and down.
⁄4
(When AMP mode is selected)
Used to turn off the video signal.
⁄5 DISC+/CH. SEL button
(When AMP mode is selected)
Used to call up SETUP MAIN MENU and adjust speaker levels or 7.1 ch input level.
⁄6 BASS +/- buttons
These buttons are used to adjust the tone control of low frequency sound for left, right and subwoofer speaker.
⁄7 SEND indicator
Indicates when the remote controller is transmitting a signal.
⁄8 
/ POWER ON and OFF buttons
(When AMP mode is selected)
These buttons are used to turn the SR6001 on or off.
⁄9 SURROUND button
This button is used to selects the surround mode.
¤0 P.DIRECT button
When this button is pressed, the tone control circuit is bypassed.
¤1 BAND/LIP SYNC/INPUT button
(When TUNER mode is selected)
Used to select a radio band.
(When AMP mode is selected)
Used to select LIP SYNC mode.
(When TV mode is selected)
Used to select monitor input.
¤2 T.MODE button
(When TUNER mode is selected)
Used to select auto stereo mode or mono mode when the FM band is selected.
The “AUTO” indicator lights in the auto stereo mode.
¤3 P.SCAN button
(When TUNER mode is selected)
Used to start preset scan.
¤4
This button is used to store setting to memory or program a source.
(When AMP mode is selected)
Used to turn on or off HT(Home
¤5 MUTE button
This button is used to mute the audio for the amplifier and television.
Note:
Set the AMP mode to use this button with the SR6001.
¤6 VOLUME +/- buttons
This button is used to adjust the volume for the amplifier and television.
Note:
Set the AMP mode to use this button with the SR6001.
¤7
(When AMP mode is selected)
Used to turn on and off multi speaker.
¤8 MENU button
(When AMP mode is selected)
This button is used to call up the SETUP MAIN MENU of the SR6001.
¤9 1, 2, 3, 4(CURSOR) / ENTER buttons
These buttons are used when controlling the cursor of the SR6001, DVD or other AV equipment.
‹0 EXIT button
(When AMP mode is selected)
This button is used to cancel setting in the setup menu.
‹1 SUBTITLE/ATT. button
(When AMP mode is selected)
When the input signal is too high and the voice distorts even by throttling the SR6001 VOLUME control, turn on this function.
“ATT” is indicated when this function is activated. The input level reduced. Attenuator is invalid for the output signal of “REC OUT”.
Note:
This function is unavailable while the digital input is selected.
‹2 AUDIO buttons
(When DVD mode is selected)
Used to select one of the audio language.
‹3 TREBLE +/- buttons
These buttons are used to adjust the tone control of high frequency sound for left and right speaker.
‹4 SOURCE button
These buttons are used to switch the source of your A/V Receiver / amplifer. Each time a source button is pressed, the remote control changes to the source which was pressed.
This remote control can control 12 types of equipment. To change the A/V Receiver / amplifier source, press this button twice within two seconds. The signal is sent when it is pressed the second time.
Note:
Select the AMP as the source to use this remote controll with the SR6001.
‹5 Infrared Transmitter and Learning
Sensor
This transmitter emits infrared light. Press the buttons while pointing the transmitter towards the infrared receiver window of the SR6001 or other AV equipment. Be sure to also point towards other remote controls when using the learning function.
10
