Marantz SR6001 manual Clearing Stored Preset Stations, Sorting Preset Stations, → Down

CLEARING STORED PRESET STATIONS

You can remove preset stations from the memory using the following procedure.

2.	3.					LIP SYNC/
			AUTO	2	dts	INPUT
			1		3	BAND
		2.	CS	EX/ES	VIRTUAL	T.MODE
DIGITAL			7	8	9
			4	5	6
			M-CH ST	STEREO	NIGHT	P.SCAN
SURROUND
AAC				7.1CH IN	A/D	HT-EQ
			CL	0	+10	MEMO
		3.	CH/ CAT	SPKR A/B	MUTE	VOLUME
				MULTI/ CAT	M-SPKR
			INFO			MENU

1. Recall the preset number to be cleared with the method described in “Recalling” a preset station.

2. Press the MEMORY button on the front panel or press the MEMO button on the remote.

3. The stored preset number blinks in the display for 5 seconds. While blinking, press the CLEAR button on the front panel or press the CL button on the remote.

4. “xx CLEAR” appears on the display to indicate that the specified preset number has been cleared.

Note:

•To clear all stored preset stations, press and hold the CLEAR and the ENTER buttons for two seconds.

SORTING PRESET STATIONS

AV SURROUND RECEIVER SR6001

SURROUND

DIGITAL

AAC

If you have stations memorized, and there is a gap in the sequential order:

I.e. the stations are stored as follows

1)87.1 MHz

2)93.1 MHz

3)94.7 MHz

10)105.9 MHz

(notice there is no stations programmed for pre sets for 4-9), you can have pre set 10 become pre set 5: To sort the numbers, press and hold the MEMORY and the 4 cursor buttons.

“PRESET SORT” will appear on the display and sorting will be done.

NAME INPUT OF THE PRESET STATION.

This function allows the name of each preset channel to be entered using alphanumeric characters. Before name inputting, you need to store preset stations with the preset memory operation.

4.5. 2. 5. 6.

AV SURROUND RECEIVER SR6001

2. 5. 6.	7	8	9
		7.1CH IN	A/D	HT-EQ
	CL	0	+10	MEMO
	CH/ CAT SPKR A/B		MUTE	VOLUME
		MULTI/ CAT	M-SPKR
	INFO			MENU
		ENTER
	T.TONE
	/SET UP			EXIT
	REC	T.DISP	PTY	F.DIRECT
5.	- PRESET +		- TUNING +
	DISC+	ANGLE	SUB TITLE	AUDIO
4. 6.	CH-SEL V-OFF		ATT.
		BASS	TREBLE
	TV	DVD	VCR	DSS

1. Recall the preset number to be inputted name with the method described in “Recalling” a preset station.

2. Press the MEMORY button on the front panel or press the MEMO button on the remote for more than 3 seconds.

3. The left most column of the station name indicator flashes, indicating the character entry ready status.

4. When you press the 3 or 4 cursor buttons on the front panel or the TUNING + or – buttons on the remote control unit, alphabetic and numeric characters will be displayed in the following order:

A → B → C ... Z → 1 → 2 → 3 ..... 0 → – → +

→/ → (Blank) → A UP →

→DOWN

5. After selecting the first character to be entered, press the MEMORY or ENTER button, or press the MEMO button on the remote.

The entry in this column is fixed and the next column starts to flash. Fill the next column the same way.

To move back and forth between the characters, press the 1/ 2cursor buttons or press PRESET

+or – button on the remote.

Note:

•Unused columns should be filled by entering blanks.

6.To save the name, press the MEMORY or ENTER button on the front panel, or press the MEMO button on the remote for more than 2 seconds.

Instead of using the 3 and 4 cursor buttons or the TUNING + or – buttons of the remote controller unit to select characters, characters can be input from the numeric keys of the remote control unit. See the below table for a correspondence between characters and numeric keys.

Ten keypad	Press, press again, press again, etc.
1	A → B → C → 1 → A
2	D → E → F → 2 → D
3	G → H → I → 3 → G
4	J → K → L → 4 → J
5	M → N → O → 5 → M
6	P → Q → R → 6 → P
7	S → T → U → 7 → S
8	V → W → X → 8 → V
9	Y → Z → space → 9 → Y
0	– → + → / → 0

ENGLISH

55