HDMI
| SYMPTOM |
| CAUSE |
| REMEDY | |
|
|
| ||||
The display does not | The connected monitor or projector |
| ||||
appear over an HDMI | does not support HDCP. |
| ||||
connection. |
|
|
|
|
| |
| The HDMI input of on the TV is | Set HDMI input so that it turns on, as | ||||
|
|
| ||||
|
|
| not on. |
| explained in the TV's instruction manual. | |
|
|
|
|
| ||
|
|
| The HDMI output on the source | Set HDMI output so that it turns on, as | ||
|
|
| component (DVD, Set Top Box, | explained in the source component's | ||
|
|
| etc.) is not on. |
| instruction manual. | |
|
|
|
|
| ||
|
|
| The HDMI mode is not correctly | Set HDMI input on the FUNC INPUT | ||
|
|
| set on the SR6001. |
| SETUP menu as explained on page 29. | |
|
|
|
|
| ||
|
|
| The HDMI output video resolution | Set the resolution so that it matches, as | ||
|
|
| of the source component (DVD, | explained in the instruction manuals of both | ||
|
|
| Set Top Box, etc.) does not match | components. | ||
|
|
| the TV specifications. |
|
| |
|
|
|
|
| ||
|
|
| The device is connected with a | A 5 m or shorter cable is recommended to | ||
|
|
| ensure stable operation and prevent image | |||
|
|
|
|
|
| quality deterioration. |
|
|
|
|
| ||
|
|
| Power to the SR6001 is off. | Turn on the power to the SR6001. | ||
|
|
| (When the SR6001 is on standby, |
| ||
|
|
| HDMI connections cannot be |
| ||
|
|
| turned on.) |
|
| |
|
|
|
|
|
|
|
|
|
| The | connection | between | Shut off and then turn the power back on to |
|
|
| HDMI | components | was not | the SR6001, TV and source component. |
|
|
| authenticated. |
|
| |
|
|
|
|
| ||
Time is needed for the | The | connection | is being | There is nothing wrong with the system. | ||
display of an | HDMI | authenticated between the HDMI | Some HDMI devices require time for | |||
connection to appear. | devices. |
| authentication. | |||
|
|
|
|
| ||
Audio | is not | played | The HDMI audio output of the | Set the HDMI audio output so that it turns | ||
back | over an | HDMI | source component (DVD, Set Top | on, as explained in the source component's | ||
connection. |
| Box, etc.) is not on. |
| instruction manual. | ||
|
|
|
|
| ||
|
|
| The signal format of the source | Set the HDMI audio output so that it can | ||
|
|
| component (DVD, Set Top Box, | connect to the SR6001, as explained in the | ||
|
|
| etc.) is not supported by the | source component's instruction manual. | ||
|
|
| SR6001. |
|
| |
|
|
|
|
| ||
|
|
| The SR6001 is set to the HDMI | In the “THROUGH” mode, sound is not | ||
|
|
| audio “THROUGH” mode. | produced from the SR6001. Set it to | ||
|
|
|
|
|
| “ENABLE”. (see page 40) |
|
|
| ||||
The DVD player does not support | • Use a | |||||
back | over an | HDMI | CPPM, therefore it cannot output | CPPM. | ||
connection. |
| HDMI audio. |
| • Turn on PCM downsampling on the DVD | ||
|
|
|
|
|
| player. |
|
|
|
|
|
| • Use an analog connection. |
|
|
|
|
|
|
|
TROUBLESHOOTING
If a problem should arise, first check the following.
1.Are the connections correct?
2.Have you operated the receiver according to the operating instructions?
3.Are the speakers and other components operating properIy?
If this unit is not operating properly, Check the items listed in the table beIow. Should the problem persist, there may be a malfunction. Disconnect the power immediately and contact your store of purchase.
SYMPTOM | CAUSE | REMEDY |
|
|
|
“ANTENNA” is displayed. | XM terminal and the XM | Check that the connection are correct. |
| Home Dock is not properly connected. |
|
|
|
|
“NO SIGNAL” is displayed. | The signal cannot be received. | Reposition your XM |
|
| Dock. |
Receiving only XM channels 0 and 1. | The XM Tuner is not activated. | Contact XM Radio. |
|
|
|
ENGLISH
63