Marantz SR6001 Auto Setup MultEQ Setup feature, Automatically optimizes settings, Listening area

ENGLISH		2-1 AUTO SETUP (MultEQ™ SETUP)
	The AUTO SETUP (MultEQ™ Setup) feature of
	the SR6001 measures sound characteristics of the
	speaker system and room where the receiver is used
	and automatically optimizes settings.
	The Audyssey MultEQ™ technology adopted by the
	SR6001 provides the best listening environment for
	multiple listeners.
	To do this, the AUTO SETUP feature measures a
	test tone emitted by each channel in a maximum of 6
	listening positions, using the supplied microphone.
	The measurement results are analyzed using an
	original algorithm and environmental settings are
	made to improve the sound characteristics of the
	listening area.

Note:

•A special microphone (ACM1, option) is needed to use the Audyssey MultiEQ function. Contact a Marantz Authorized Dealer or Customer Support regarding purchase of this microphone.

To set up the speaker system (i.e., adjusting speaker distance, etc.) without using the AUTO SETUP feature, see “MANUAL SETUP” on page 35 of the manual.

HOW TO PERFORM AUTO SETUP

During measurement, the OSD menu displays the condition, therefore turn power to the monitor on.

1. Connect the supplied microphone to the MIC jack on the SR6001.

Notes:

•Measurement can be done in a maximum of 6 listening positions.

For the first measurement, set the microphone in the main listening position.

•Use a stand or tripod to position the microphone at ear height in the listening position.

•Remove any obstructions between the speakers and microphone.

•To use the internal subwoofer of the amp, set the volume to the middle point and set the crossover frequency to the highest.

•Duringmeasurement,stepawayfromthemicrophone and operate the SR6001 via the remote control unit from a position that is out of the path of the speaker sound.

•The test tone output from the speakers during measurement is loud. Be mindful of neighbors and watch out for small children.

3.Either press the MultEQ™ button on the front panel of the SR6001 or select “2. SPKR SETUP” from the MAIN MENU, select “AUTO SETUP” with the 3/4 cursor buttons, and press the ENTER button to display the start screen.

4.Select the number of channels for the surround back speaker you are using.

For a 5.1 channel speaker system, select “NON” (Surround Back speaker off). (To use speaker C or multi speaker, select “NON”. See page 24, 41.)

Select “START” with the 3/4 cursor buttons and press the ENTER button to start measurement.

5.	Detection Check					After confirming the check results, select
						“RETURN” with the 3/4 cursor buttons and
	During the detection check, the following OSD
						press the ENTER button to return to the OSD
	appears on the display and checks are made
						menu.
	to detect dark sound in the listening room,
						At this point, you can select “EXIT” to end Auto
	whether there are speakers or not and polarity.
						Setup and return to “2. SPKR SETUP”.
		AUTO		SETUP
		SPEAKERS		CHECK: --		7. Calibration Check
		NOW ANALYZING !!
						AUTO	SETUP
			CANCEL
						SPEAKERS	CHECK:OK
						1ST MIC	POSITION!!
					EXIT	START
						CHECK
Note:
	• The detection check measures the state of use of all						EXIT
	speakers whether actually used or not.
	For example, if the center speaker is not used, the					Select “START” with the 3/4 cursor buttons
	test tone will require time to go from the L-channel					and press the ENTER button to measure the
	to the R-channel, therefore be careful not to unplug
						first point (main listening position).
	the microphone or operate the SR6001 during this
	time.					During measurement, the following OSD
						appears on the display. At this point, you can
6.	When the detection check ends, the following					cancel measurement by selecting “CANCEL”
	OSD appears on the display.					with the 3/4 cursor buttons and pressing the
						ENTER button.
		AUTO		SETUP
		SPEAKERS		CHECK:OK		AUTO	SETUP
		1ST MIC		POSITION!!
			START			NOW ANALYZING!!
			CHECK
						CANCEL
					EXIT
							EXIT

2. Set the microphone in the listening position.

AUTO SETUP

AUTO SETUP: START

MAIN ROOM

SURR BACK: 2CH

RETURNEXIT

Here, to view the results of the detection check, select “CHECK” with the 3/4 cursor buttons and press the ENTER button. The results will be displayed.

SPEAKER		CONFIG
CHECK	!!	SPEAKER
FRONT	: YES
CENTER	: NON
FRONT R	: YES
SURR . R	: YES
SURR . B R : NON
SURR . B L : NON
SURR . L	: YES
SUB W	: YES
RETURN		EXIT

When this measurement ends, the following OSD appears on the display

AUTO SETUP

SPEAKERS CHECK:OK

2ND MIC POSITION!!

START

CALCULATE

EXIT

Ifthecheckresultsindicateanerror,takesuitable action with that item and remeasure. (For error messages, see “ERROR MESSAGES” on page 34.)

32