Marantz SR6001 manual To check equalizer MultEQ parameters, see

8. 8. Move the microphone to the second listening position, select “START” with the 3/4 cursor buttons and press the ENTER button to measure the second point. At this point, you can cancel second point measurement and calculate measurement results by selecting “CALCULATE” and pressing the ENTER button.

AUTO SETUP

SPEAKERS CHECK:OK

2ND MIC POSITION!!

START CALCULATE

EXIT

9. Repeat steps 7 and 8 until measuring 6 points between the main listening position and surrounding positions.

When all measurements end, the following OSD appears on the display.

AUTO SETUP

SPEAKERS CHECK:OK

CALCULATE

EXIT

Select “CALCULATE” with the 3/4 cursor buttons and press the ENTER button to calculate measurement results. During calculations, the following OSD appears on the display.

AUTO SETUP

______________

NOW CALCULATE !!

EXIT

Note:

•Less than 6 positions can be measured, but it is recommended to measure in all 6 positions in order to obtain the best results.

•The time needed to complete calculations depends on the number of connected speakers and measured listening positions. The more speakers and listening positions, the more time is needed.

10. Checking Measurement Results

When calculations for the measurement results end, a screen appears for confirming the calculation results.

CHECK RESULT

SPEAKER CONFIG

SPEAKER SIZE

DISTANCE

CHANNEL LEVEL

CROSSOVER FREQ

STORE

EXIT

Select items to check with the 3/4 cursor buttons and press the ENTER button to enter them.

Note:

To check equalizer (MultEQ) parameters, see page 43.

[Example] Confirmation screen for speaker detection

SPEAKER		CONFIG
CHECK	!!	SPEAKER
FRONT	: YES
CENTER	: NON
FRONT R	: YES
SURR . R	: YES
SURR . B R : NON
SURR . B L : NON
SURR . L	: YES
SUB W	: YES
RETURN		NEXT

[Example] Confirmation screen for the distance from speakers to the listening position

		DISTANCE
UNIT			:	ft
FRONT	L		:	30 . 00ft
CENTER			:	19 . 33ft
FRONT	R		:	29 . 66ft
SURR . R			:	21 . 50ft
SURR . B		R	:	12 . 33ft
SURR . B		L	:	11 . 66ft
SURR . L			:	16 . 33ft
SUB W			:	12 . 50ft
RETURN				NEXT

*The units can be changed by moving the cursor to [ft] of UNIT and pressing 1 / 2 the cursor buttons. Each time a 1 / 2 cursor button is pressed, the units alternate between [ft] (feet) and [m] (meters).

[Example] Confirmation screen for speaker size and crossover frequency

SPEAKER			SIZE
FRONT	L		: AUTO
CENTER			: AUTO
FRONT	R		: AUTO
SURR . R			: AUTO
SURR . B		R	: AUTO
SURR . B		L	: AUTO
SURR . L			: AUTO
SUB W			: AUTO
RETURN			NEXT
CROSSOVER FREQ
FRONT		: AUTO
CENTER		: AUTO
SURR		: AUTO
SURR . B		: AUTO

RETURN

*AUTO is displayed to indicate that the speaker size and crossover frequency results were automatically measured.

11. Storing Measurement Results in Memory

Once finished confirming the measurement results, select “RETURN” with the 3/4 cursor buttons and press the ENTER button to display the CHECK RESULT screen.

CHANNEL			LEVEL
FRONT	L	:	0	. 0dB
CENTER		: - 6 . 5dB
FRONT	R	: - 1 . 5dB
SURR . R		:	+1	. 0dB
SURR . B	R	:	+9	. 5dB
SURR . B	L	:	+12	. 0dB
SURR . L		: - 2 . 5dB
SUB W		: - 12 . 5dB
RETURN			NEXT

CHECK RESULT

SPEAKER CONFIG

SPEAKER SIZE

DISTANCE

CHANNEL LEVEL

CROSSOVER FREQ

STORE

EXIT

Place the cursor on “STORE” and press the ENTER button to store all parameters including the equalizer parameters in memory. If not wanting to store the calculation results in memory, place the cursor on “EXIT” and press the ENTER button.

Note:	ENGLISH
Pressing “EXIT” prior to pressing “STORE” erases all
measurement results and calculation results, therefore
operate the remote control unit with care.
When storing operations end, the following OSD
appears on the display.
2 . SPKR SETUP
AUTO SETUP
MANUAL SETUP

RETURN EXIT

Note:

•Do not turn the power to the SR6001 off while storing parameters in memory. This may erase all data in the SR6001’s memory and may damage the receiver.

33