Marantz SR6001 Other Function, Attenuation To Analog Input Signal, Auto Power On, Auto Power Off

OTHER FUNCTION

ATTENUATION TO ANALOG INPUT SIGNAL DOLBY HEADPHONE MODE

VIDEO ON/OFF

ENGLISH	TV AUTO ON/OFF FUNCTION
	This function allows the component connected to the
	TV-VIDEO in jack to control the power (ON/OFF) to
	the SR6001.
	AUTO POWER ON
	1.	Be sure the TV auto mode is ENABLED. (Refer
		to page 39: PREFERENCE)
	2.	Connect your TV TUNER (etc) to the TV-
		VIDEO in terminal. Be sure to connect the
		VIDEO input.
	3.	Turn OFF the power to the TV TUNER and the
		SR6001.
	4.	Turn ON the TV TUNER and tune in a receivable
		station.
	5.	When the station is received, the SR6001 turns
		ON and TV is selected automatically.

AUTO POWER OFF

1. In the above situation, turn the TV TUNER OFF or select a channel that does not contain any broadcast.

2. The power to the SR6001 switches to STANDBY

REC	T.DISP	PTY	F.DIRECT
- PRESET +		- TUNING +
DISC+	ANGLE	SUB TITLE	AUDIO
CH-SEL V-OFF		ATT.
	BASS	TREBLE
TV	DVD	VCR	DSS
TUNER	CD	CDR	MD

If the selected analog audio input signal is greater than the capable level of internal processing, the “PEAK” indicator will light up on the front display. If this happens, you should press the ATT button on the remote.

“ATT” indicator will be illuminated when this function is activated. The signal-input level is reduced by about half. Attenuation will not work with the output signal of TAPE-OUT, CD/CD-R and VCR OUT.

This function is memorized for each individual input source.

LISTENING THROUGH HEADPHONES

This jack may be used to listen to the SR6001’s output through a pair of headphones. Be certain that the headphones have a standard 1/4” stereo phono plug. (Note that the speakers will automatically be turned off when the headphone jack is in use.)

This feature simulates the waveforms of the actual sounds heard from the speakers.

When headphones are used, the MENU button automatically switches to the Dolby headphone mode.

The OSD that appears when the MENU button is pressed is shown below.

	HEAD	PHONE
DOLBY HP		MODE :DH
SURROUND		:PL I MV
L	LEVEL	:+10 . 0dB
R	LEVEL	:	0 . 0dB

DOLBY HP (Headphone) MODE can be selected with the left and right cursor buttons.

BYPASS → DH (DOLBY Headphone) → BYPASS

BYPASS: Bypasses the Dolby headphone mode and delivers ordinary 2-channel stereo.

DH: Dolby Headphone is a signal processing system that delivers a sound similar to room speakers.

It makes it possible to experience the volume and space of a 5-channel surround system using ordinary stereo headphones.

When no video signal is connected to the SR6001 or a DVD, etc., is connected directly to your TV, the unnecessary video circuit can be turned off by selecting the “VIDEO OFF” setting.

To select video off, press the AMP button and press the V-OFFbutton.

TV	DVD	VCR	DSS
TUNER	CD	CDR	MD
UND RECEIVER SR6001
TAPE	AUX1	AUX2	AMP
SURROUND	REMOTE CONTROLLER
DIGITAL
AAC	RC5001SR

REC T.DISP PTY F.DIRECT

- PRESET +		- TUNING +
DISC+	ANGLE	SUB TITLE	AUDIO
CH-SEL V-OFF		ATT.
	BASS	TREBLE
TV	DVD	VCR	DSS

after approx. 5 minutes.

Notes:

•AUTO POWER OFF is canceled if the SR6001 is set to a source other than TV.

The function reactivates when TV is selected again.

•Some TV broadcasts may cause the TV AUTO FUNCTION to turn ON.

•The S-Video terminal does not support “TV AUTO ON/OFF” function.

AV SURROUND RECEIVER SR6001

	When the PURE DIRECT mode is selected, Dolby
	surround processing is bypassed and “✽✽✽” is
	displayed as the mode indication.
	The surround mode can be selected when the
	modes in DH is selected.
	L/R LEVEL can be set in the ±12 dB range.
	Notes:
	• The surround mode returns to the previous setting as
Note:	soon as the plug is removed from the jack.
• The surround mode returns to the previous setting as	• TONE and ACOUSTIC EQ cannot be set when the
	DH mode is selected.
soon as the plug is removed from the jack.

50