Marantz SR6001 manual Learn Mode, Learning Procedure

ENGLISH

LEARN MODE

This remote control is capable of learning and storing codes used by other remote controls that you already own.

For codes which are not learned, the remote control will transmit either the Marantz preset codes from the initial settings, or remote codes from another manufacturer’s AV equipment which is set by the customer.

The receiver sensor for the remote control signals is located at the top of the remote control.

Notes:

•This remote control is capable to learn around 60 codes.

•When the batteries are getting weak , the learing procedure is not successful.

LEARNING PROCEDURE

1. Place the remote controller so that its infrared signal transmitter is facing the infrared signal receiver on the Marantz remote controller at a distance of about 0.05 m (2 inches).

2. Press and hold down the SET and MENU buttons until LEARN indicator blinks.

				MULTI/ CAT	M-SPKR
SOURCE	SET	OFF	ON
l/
SLEEP	DISPLAY	P.DIRECT	SURROUND	INFO	MENU
			LIP SYNC/
AUTO		dts	INPUT
1	2	3		ENTER

3. Select the SOURCE button to select the

SOURCE.

	BASS		TREBLE
TV	DVD	VCR	DSS
TUNER	CD	CDR	MD
TAPE	AUX1	AUX2	AMP
	REMOTE CONTROLLER
	RC5001SR

4. Select the button to be learned.

• LEARN indicator lights up.

l/

SLEEP DISPLAY P.DIRECT SURROUND

			LIP SYNC/
AUTO		dts	INPUT
1	2	3
CS	EX/ES	VIRTUAL	T.MODE

4 5 6

5. Press and hold the button of the original remote controller to learn until the SEND indicator blinks twice.

•When the SEND indicator blinks once, repeat this step.

•When the memory of the RC5001SR is full, the LEARN and SEND indicators blink once. If you want to learn the code, you should erase other learned button.

6.Repeat steps 4 and 5 to learn other buttons in same SOURCE.

7.Repeat steps 3 to 6 to learn other SOURCE.

8.When you have finished programming the remote controller, press the SET button, then LEARN indicator stops blinking and exits from the LEARN mode.

LEARNSEND

SOURCE SET OFF ON l/

SLEEP DISPLAY P.DIRECT SURROUND

		LIP SYNC/
AUTO	dts	INPUT

Notes:

•When the SEND indicator blinks once again, the transmitting code is unavailable for RC5001SR, or the transmitting signal is intercepted by noise.

•If no buttons are pressed for approximately 1 minutes while in the LEARN mode, the remote controller automatically exits from the LEARN mode.

ERASING PROGRAMMED CODES

(RETURNING TO INITIAL SETTINGS)

Codes can be erased in three ways: by buttons, sources, and by all memory contents.

Erasing the code by buttons

1. Press and hold down the SET and MENU buttons until LEARN indicator blinks.

				MULTI/ CAT	M-SPKR
SOURCE	SET	OFF	ON
l/
SLEEP	DISPLAY	P.DIRECT	SURROUND	INFO	MENU
			LIP SYNC/
AUTO	2	dts	INPUT
1		3		ENTER

2. Select the SOURCE button to select the button to be erased.

	BASS		TREBLE
TV	DVD	VCR	DSS
TUNER	CD	CDR	MD
TAPE	AUX1	AUX2	AMP

REMOTE CONTROLLER

RC5001SR

3. Press and hold down the SLEEP button and press the learned button twice to be erased.

•SEND indicator blinks twice and the mode returns to LEARN mode.

SOURCE SET OFF ON l/

SLEEP DISPLAY P.DIRECT SURROUND

		LIP SYNC/
AUTO	dts	INPUT

1 2 3

4. To return the NORMAL mode, press the SET button.

Erasing the code by SOURCE

1. Press and hold down the SET and MENU buttons until LEARN indicator blinks.

				MULTI/ CAT	M-SPKR
SOURCE	SET	OFF	ON
l/
SLEEP	DISPLAY	P.DIRECT	SURROUND	INFO	MENU
			LIP SYNC/
AUTO		dts	INPUT
1	2	3		ENTER

2. Press and hold down the SLEEP button and press the learned SOURCE button twice to be erased.

• LEARN indicator lights.

			CH-SEL V-OFF		ATT.
SOURCE	SET	OFF	ON	BASS		TREBLE
l/			TV	DVD	VCR	DSS
SLEEP	DISPLAY	P.DIRECT	SURROUND
			TUNER	CD	CDR	MD
			LIP SYNC/
AUTO		dts	INPUT
1	2	3	TAPE	AUX1	AUX2	AMP

3. Press ENTER button to continue erasing.

•The SEND indicator blinks twice and the mode returns to LEARN mode.

•To cancel the erasing operation, do not press ENTER button and simply touch any

other button.

INFO	MENU
	ENTER
T.TONE
/SET UP	EXIT

4. To return the NORMAL mode, press the SET button.

Erasing the all SOURCES

1. Press and hold down the SET and MENU buttons until LEARN indicator blinks.

				MULTI/ CAT	M-SPKR
SOURCE	SET	OFF	ON
l/
SLEEP	DISPLAY	P.DIRECT	SURROUND	INFO	MENU
			LIP SYNC/
AUTO	2	dts	INPUT
1		3		ENTER

2. Press and hold down the SLEEP button and press POWER ON and POWER OFF button.

• LEARN indicator lights.

SOURCE	SET	OFF	ON
l/
SLEEP	DISPLAY	P.DIRECT	SURROUND
			LIP SYNC/
AUTO		dts	INPUT

1 2 3

3. Press ENTER button to continue erasing.

•The SEND indicator blinks twice and the mode returns to LEARN mode.

•To cancel the erasing operation, do not press ENTER button and simply touch any

other button.

INFO	MENU
	ENTER
T.TONE
/SET UP	EXIT

4. To return the NORMAL mode, press the SET button.

Note:

Erasing codes will return to the factory preset code, or there will leave empty if the button has no factory preset code.

16