Marantz SR8001, SR7001 manual Remote Control Range, Battery Replacement Interval, Setting the Time

REMOTE CONTROL RANGE

The distance between the transmitter of the remote control and the IR SENSOR of the SR7001 should be less than 5 meters. If the remote control is pointed in

3. Close the cover until it clicks.

BATTERY REPLACEMENT INTERVAL

Under normal usage, alkaline batteries last approximately four months. When the batteries wear out, a battery mark is displayed on the LCD. Although

SETTING THE TIME

Example: Setting to 6:20PM (18:20)

12

ENGLISH

a direction other than the IR SENSOR or if there is an obstacle between them, use of the remote control may not be possible.

Remote-controllable range

SR7001

60°

CAUTIONS ON BATTERIES

•	Use “AAA” type batteries in this remote control
	unit.
• We recommend that you use alkali batteries.
•	If the remote control unit does not operate from
	close to the main unit, replace the batteries with

the remote control can still be used when the battery mark is displayed, the batteries should be replaced as soon as possible. The LCD eventually starts to flash when buttons are pressed, the remote control will be unable to transmit signals or learn codes.

•This remote control uses non-volatile memory so that the learned codes and macro programs are retained even if the batteries are removed.

Reset the clock after replacing the batteries.

Safety Precautions for Batteries

Be sure to always observe the following precautions to prevent fluid leakage, overheating, fire, breakage,

POWER

OFF	ON/OFF	ON
	SOURCE
		M
		D1
		D2
		D3
		D4
		D5
CH		VOL
	OK
	LIP.SYNC
PREV		MUTE
	GUIDE
MENU		EXIT
TEST	CH.SEL	SURR
1	2	3
7.1CH	ATT	SPK-AB
4	5	6
DISP	OSD	SLEEP
7	8	9

1.

3.

USE PAGE 1

2.

3

6.

LEARN

4.

5.

USE PAGE 1 2

4

LEARN

Remote control unit (RC8001SR)

LOADING BATTERIES

The life of the batteries used with the remote control is about 4 months with normal use. Also be sure to replace batteries earlier when you notice that they are getting weak.

1. Remove the back cover.

2. Insert the new batteries (AAA type) with correct and polarity.

	new ones, even if less then a year has passed.
• The included battery is only for verifying operation.
	Replace it with a new battery as soon as
	possible.
• When inserting the batteries, be careful to do so in
	the proper direction, following the + and - marks in
	the remote control unit’s battery compartment.
• To prevent damage or battery fluid leakage:
	- Do not use a new battery with an old one.
	- Do not use two different types of batteries.
	- Do not short-circuit, disassemble, heat or
	dispose of batteries in flames.
•	Remove the batteries when not planning to use
	the remote control unit for a long period of time.
•	If the batteries should leak, carefully wipe off the
	fluid from the inside of the battery compartment,
	then insert new batteries.
• When disposing of used batteries, please comply
	with governmental regulations or environmental
	public instruction’s rules that apply in your country
	or area.

accidental ingestion, and other accidents.

•If the batteries are left unused for a long period of time, the battery fluid may leak or the batteries may corrode.

•Do not use the batteries in the remote control with the plus and minus polarity reversed.

•Do not attempt to recharge, heat, or disassemble the batteries. Do not put the batteries in a fire.

•Do not use the remote control with old batteries or worn-out batteries inserted.

•Do not use different types of batteries or mix old and new batteries in the remote control.

•If the remote control is not operating properly, replace the batteries with new ones.

•If any of the batteries are leaking, completely wipe up all leaked battery fluid, and then replace the batteries with new ones.

	THX
CLEAR	0		MEMO	5	6
TV	DVD	VCR	DSS
TUNER	CD	CD-R	MD
TAPE	AUX1	AUX2	AMP		LEARN
	LIGHT
1			2
	RC8001SR
	Learning Remote Controller

USE PAGE 1 2

When you bought this remote control and insert the batteries to the remote control at first, the steps 1 to 3 are skipped.

Starts from step 4 to set the time.

1. Hold down the M button for three seconds or more.

The menu is displayed.

2. Press the > button once.

This displays second page (SETUP).

3. Press the D4 (CLOCK) direct button.

The “ ” indicator blinks and the clock indicator displays “0:00”.

4. Press the 1 and 8 numeric button to set the hour indicator.

The hour indicator displays “18”.

The minute indicator blinks “_”.

5. Press the 2 and 0 numeric button to set the minute indicator.

The minute indicator displays “20”.

The hour indicator blinks.

6. Press the OK cursor button to start the clock.

The clock starts from 0 second at the time that was set and return to normal (USE) mode.

Whenever the batteries are replaced, the clock shows 00:00. Please reset the clock. (The time setting is not backed up.)

11