Marantz SR7001, SR8001 manual TV Auto ON/OFF Function, Listening Through Headphones, Auto Power on

OTHER FUNCTION

ATTENUATION TO ANALOG INPUT SIGNAL DOLBY HEADPHONE MODE

VIDEO ON/OFF

ENGLISH	TV AUTO ON/OFF FUNCTION
	This function allows the component connected to the
	TV-VIDEO in jack to control the power (ON/OFF) to
	the SR7001.
	AUTO POWER ON

	LIP.SYNC
PREV		MUTE
	GUIDE
MENU		EXIT
TEST	CH.SEL	SURR
1	2	3
7.1CH	ATT	SPK-AB
4	5	6
DISP	OSD	SLEEP
7	8	9
	THX
CLEAR	0	MEMO

This feature simulates the waveforms of the actual sounds heard from the speakers.

When headphones are used, the MENU button automatically switches to the Dolby headphone mode.

The OSD that appears when the MENU button is pressed is shown below.

HEAD PHONE

When no video signal is connected to the SR7001 or a DVD, etc., is connected directly to your TV, the unnecessary video circuit can be turned off by selecting the “VIDEO OFF” setting.

To select video off, press the AMP button and press the > button until PAGE 4 is displayed. Press the V-OFFbutton.

M

D1

1.	Be sure the TV auto mode is ENABLED. (Refer
	to page 35: PREFERENCE)
2.	Connect your TV TUNER (etc) to the TV-
	VIDEO in terminal. Be sure to connect the
	VIDEO input.
3.	Turn OFF the power to the TV TUNER and the
	SR7001.
4.	Turn ON the TV TUNER and tune in a receivable
	station.
5.	When the station is received, the SR7001 turns
	ON and TV is selected automatically.

AUTO POWER OFF

1. In the above situation, turn the TV TUNER OFF or select a channel that does not contain any broadcast.

2. The power to the SR7001 switches to STANDBY

after approx. 5 minutes.

Notes:

• AUTO POWER OFF is canceled if the SR7001 is

set to a source other than TV.

The function reactivates when TV is selected again.

• Some TV broadcasts may cause the TV AUTO

FUNCTION to turn ON.

		DOLBY HP MODE : DH
If the selected analog audio input signal is greater
		SURROUND		: PL II
					CINEMA
than the capable level of internal processing, the
“PEAK” indicator will light up on the front display. If		L	LEVEL	: +10dB
		R	LEVEL	:	0dB
this happens, you should press the ATT button on
the remote.
“ATT” indicator will be illuminated when this function
is activated. The signal-input level is reduced by
about half. Attenuation will not work with the output	DOLBY HP (Headphone) MODE can be selected
signal of TAPE-OUT, CD/CD-R, VCR1-OUT and
	with the left and right cursor buttons.
DSS/VCR2-OUT.
	BYPASS → DH (DOLBY Headphone) → BYPASS
This function is memorized for each individual input
source.	BYPASS: Bypasses the Dolby headphone mode
		and delivers ordinary 2-channel stereo.
	DH: Dolby Headphone is a signal processing
LISTENING THROUGH HEADPHONES
		system that delivers a sound similar to
		room speakers.
This jack may be used to listen to the SR7001’s
		It	makes it possible to experience
output through a pair of headphones. Be certain that
		the volume and space of a 5-channel
the headphones have a standard 1/4” stereo phono
		surround system using ordinary stereo
plug. (Note that the speakers will automatically be
		headphones.
turned off when the headphone jack is in use.)	When the PURE DIRECT mode is selected, Dolby

AV SURROUND RECEIVER SR8001	surround processing is bypassed and “✽✽✽” is
	displayed as the mode indication.
	The surround mode can be selected when the
	modes in DH is selected.
	L/R LEVEL can be set in the ±12 dB range.

UND RECEIVER SR8001
	D2
	D3
SURROUND
DIGITAL
AAC	D4
USEPAGE	4
	D5

CH			VOL
TUNER	CD	CD-R	MD
TAPE	AUX1	AUX2	AMP
		LIGHT
1			2

RC8001SR

Learning Remote Controller

• The S-Video terminal does not support “TV AUTO

ON/OFF” function.

Note:

•The surround mode returns to the previous setting as soon as the plug is removed from the jack.

Notes:

•The surround mode returns to the previous setting as soon as the plug is removed from the jack.

•TONE cannot be set when the mode in DH is selected.

•The Dolby Headphone function will not work when 32 or 96 kHz PCM digital signals are input.

46